I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi there!
I'm trying to make an SH1106 screen working with my Zephyr 3.7.0 project using an nRF52DK (nrf52832-based one). My project is straightforward:
proj.conf
...
Hello,
I am attempting to use the DFU Target library to receive an update file over a custom protocol. I aim to do an MCUboot-style upgrade such that after the file upload...
Hi there,
My compiled image size in ROM is ~200kb.
I have 2 MCUboot partiitons, each 228kB.
I wanted to ask- is it possible for the application to use the second (non...
NCS v2.7.0
nRF52840 dongle
I want to program the nRF52840 dongle with external J-Link, and I can connect to nRF52840 dongle with SWD now. Using "nRF52840 Dongle nRF52840...
Hi,
I am evaluation PAWR feature and plan to use it for a product. The project is based on nrf5340.My enviroment is:
nrfconnect sdk v2.7.0
nrf5340 audio dk.
After...
Need to automate the FOTA process for devices with Zephyr build application which has mcuboot as bootloader, these devices can be programmed using nRF Device Manager and nRF...
I’m developing a product that uses the nRF9160 for LTE-M and the nRF52840 for Bluetooth. The nRF52840 is a pre-certified module, and I have experience with FCC compliance...
Is there any hardware limitations that would prevent one from using the nrf_802154 drivers on an nRF9161? If no, could you adapt the open-source sl to use the 9161 modem instead...
Setup: custom nrf9161 PCB, flashed with nrf9161 modem fw 2.0.1, using NCS 2.6.1
Targeting my custom board, I couldn't even speak to the modem lib, no IMEI etc.
So I dug...
Hello,
I have been trying to correctly setup my nRF Connect inside VS Code.
When I try to execute the command
west -V
in a nRF Connect window inside VS Code, I...
Hi i am using nRF52840 with segger embedded studio.
SDK -> nrf5-sdk 17.1.0 I want to configure rtc2 so that whenver i initialize it it should generate an interrupt after...
Hello, I am building a device which simultaneously advertises as a beacon and acts as a peripheral role device. Advertisements are sent at ~20 Hz with the connection to the...
hi:
I am use broadcast_sink and broadcast_source of nrf5340_audio simultaneously. use a button to switch source or sink. i am use NCS v2.6.2 if switch to sink mode is show...
Hello friends, I am using nrf52833 MCU for my current project, this project involves a sensor from infineon that operate on SPI and it supports high frequencies up to 50 MHz...
Hi,
I referred to the DevAcademy FOTA over Bluetooth Low Energy, but in the provided code, the BLE mobile app connects to the device and it automatically enters DFU mode...
