In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi I would like some advice on where to start learning Nordic BLE?
All I could find by searching was advice from 6-9 years ago, I think today they are not relevant, because...
hello,
I'm doing a power consumption test, but I'm not sure which project to use to test the power consumption.I tried the "peripheral_lbs" download with NCS version 2.8...
My setup: SDK version: 2.5.0.v Modem version: 1.3.0. I am using MQTT to subscribe to a topic, for example, the LED state. The plan is t o set the LED state on the server side...
Hi,
The SDK version I am using is 2.6.1 and the example is "matter lock".
I wrote the following configuration into \child_image\mcuboot\prj.conf.
And add the code...
Hello, thanks for reading and happy holidays!
We are using an nrf5340dk, with zephyr and SDK 2.5.0.
We seem to have two undesired behaviors from MCUBoot immediately after...
Can,t flash nRF52832 custom board using nrf connect vscode extension im trwing to use nRFconnect for my project, im using fade_led from example and got this error
i try...
Hi everyone, I have a problem when I tried to configure UART ( baudrate, parity, data_bits, stop_bits, flow_ctrl). I upload my project:
#include "myuart.h"
#include...
Hi,
I want to use nRF9160's internal RTC. I coded it but did not get the real time correctly.
SDK: 2.5.0
IDE: vs code
board: nRF9160dk
Best regards,
Liza
I'm going through the Academy courses and somewhere around Lesson 3, I could no longer flash firmware to the nrf52840 DK.
I browsed the forum and found some notes around...
nrf connect for desktop nrf54l15 device not detected by bluetooth le app
log:
12:18:38.872
Using nrf-device-lib-js version: 0.4.4
12:18:38.872
Using nrf-device...
Hi,
in Cellular Iot Fundamentals there is in lesson 4 an exercise to move to MQTT with TLS.
As I used MQTT helper library, I wonder if it is enough to modify the structure...
We had an issue with the FDS such that if the device lost power in the ~50ms window after bonding was carried out, the FDS would take longer to initialise when power was restored...
Hello,
I have read conflicting information on whether Verizon requires the LwM2M library to certify on their network. We will be certifying a nRF9151 modem.
This Nordic...
Hello,
since using Bluetooth requires an expensive qualification process, I am looking for a more affordable alternative for a startup/small business like me.
The only...
