Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi All,
SDK => v17.1.0
IDE => Segger
Project => ble_app_bps
I use LightBlue to connect my board,and going down to the device information service I choose system...
Hi,
I'm using nRF5340 DK, one board is programmed as central and 2 boards are programmed as peripherals. When I flash the central program it is selecting a random board...
Hello,
we are currently experiencing issues with the SPI interface which we suspect is due to the behaviour of the MOSI line in idle state. We have noticed that during communication...
Hello,
I am planning to test ethernet module on nRF9160, use SEGGER SDK v1.7.0 for compile the programs. In Q&A I saw using can bus module & ENC424J600 ethernet controller...
Hey,
I try to read the CRC from E-Paper display series 1.02 inch (GDEW0102L4f) with no success (I'm working with nRF52833 Development Kit)
My code and the official Goodisplay...
Hi
I can‘t find the bank size configuration in the project secure_bootloader_uart_mbr_pca10056。 For safety reasons, I want to artificially divide the size of bank0 and bank1...
Sir,
I am using a U-BLOX NINA B302 (nrf52840) connected to a SEGGER J-LINK to program it!
Using the J-LINK flash i can program the NINA B302
But, on VISUAL STUDIO +...
Hello!
I am having 3 nrf5340 devices; 2 Gateways and 1 Headset. I am trying to achieve the scenario where I can allow the Headset connects to selectively one of the 2 Gateways...
I recently got the nrf52840dk board and I am trying to use it with the Nuttx embedded OS. However, I am having some issues flashing the nuttx binary on my board.
this is...
I'm trying to accurately measure our 3.0 volt coin battery (CR2450).
Our product consume low power (<50 uA) and we measure the battery voltage every minute.
We must...
Hello,
I've been trying to get through SUPL client library license signup process but I my request get denied every time.
I think I've done everything that is required...
I wrote a firmware on my dk52 and am advertising some data to the nRF Connect for Mobile App.
Is there any way on how I can copy or send the received data (service data...
Hi,
I have the following ouput using the throughput example:
Altered output format a bit to give me the same for local and peer.
But I was wondering why there is a...
Hi All,
I am running nrfConnect SDK v1.8.0 ad started a new sample LBS project. I ultimately want to have 3 devices, 1 being a Central and 2 Peripherals both running LBS...
Hi
Nordic Team
I used nRF5_SDK_17.1.0. I have a very difficult problem:
I now only want to configure an RX pin and no TX pin. Can the serial port receive data function...
