I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
I want to use exported provision and configuration data with PyACI. I trired by copying all fileds one by one from exported json to example_database.json (which has already...
I'm seeking clarification on what all can be ran on the network core. In the Network Core introduction section of the Working with nRF53 Series page, it mentions `the network...
Hi everyone,
As I mentioned in the subject, how many time do we wait for sending Start and Disable commands after Ready and End interrupts in transmit sequence of nRF52840...
hi, i have read nrf52832/40 product specs. i want to know about system off and system on modes. i am not getting what they mean pls explain in simple words.
infocenter.nordicsemi...
I want to use the usb dfu along with the buttonless ble dfu, how can I do so? I want to use the usb to have dfu and also work as a vitual com port? Can I simple merge both...
Hello
Can you provide customer with the API of the attachment( nRF_DTM.exe application)? They want to integrate this application into their mass production tools.
Hi everybody,
I am working with two custom boards with nrf52840 chip, using the examples of UART central/peripheral.
I set power TX of connection exactly as the example...
I have got the nrf5340dk,then i using the SES IDE of windows。I open the sample named "peripheral_nfc_pairing sample",and build the solution,then debug it .After those steps...
I am attempting to advertise two sets, one using coded PHY and one using 1M, currently using the master NCS branch (post v1.7.0-rc2 tag). This is on a custom board with an...
Hello,
I have got the exact same issue as described here: https://devzone.nordicsemi.com/f/nordic-q-a/58275/zigbee-reporting-not-work-while-using-multiple-endpoints/236706#236706...
I'm running FreeRTOS with default tickless idle mode (CPU is woken up by SysTick interrupt) on NET_CPU core.
If the TAD_S module (Trace and debug control) is not enabled...
Hi Nordic team
Last week and before, I tried sdk connect v3.0.0 http_application_update example.
Everything was fine. Pressed button1 to download new bin file and then...
HI DEV
Currently we found a UART Frame error on customer product:
Application scenario diagram
Figure1
nrf52820 ,SDK17.02, softdevice:S132 , gap event length=6*1...
Hi! I'm new to zephyr and nRF boards.
I am trying to write a custom board using the nRF52811. When I try to build examples using the custom board using the command (syntax...
When I asked earlier, it was not possible to send HTTPS payloads greater than 2K due to the TLS secure socket buffer size limit. I see in the most recent modem firmware release...
