Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
I am developing an application that requires communication between two nrf52840-based devices. There is a scenario in my application where the devices needs to exchange...
Hi,
[179] RTC: COMPARE event is generated twice from a single RTC compare match
This anomaly applies to IC Rev. Revision 2, build codes CKAA-Dx0, QIAA-Dx0.
It was...
Hi everyone, I'm an intermediate level nRF Connect SDK IDE programmer, and I describe my issue below:
1.- In the link below I found an example of code for the analog port...
The SDK version is using version 17 and I am using NRF52832.
I checked the following scope waveform for the next SPI communication.
Question
I want to remove the...
nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_bootloader\pca10056_ble\arm5_no_packs
Why the compiled hex file is different from before, and the code is not modified
I like to use nRF toolbox to monitor my glucose meter. To my understanding, after the glucose device connected with nRF toolbox, they will be exchanging data. So my question...
Hi,
When attaching external GPS Antenna to Nordic Thingy91, I realize that the power consumption increases by about 5mV. Are there any ways that I can config to unuse this...
I just solved this bug, so I'll share my solution.
Bug description: cannot run application after upload via nRF Connect v3.6.1 - Programmer using MCUboot. Upload is successful...
Hello,
I am ble to connect with nRF 52840 using pygatt bluetooth command.
sudo gatttool -b E5:3B:A6:E1:58:86 -I.
[LE]:connect
[LE]:Connection Successful.
Even...
Hi,
I'm using nRF5_SDK_17.0.2_d674dde\examples\peripheral\twi_master_with_twis_slave\pca10040\blank\ses to check I2C as per infocenter TWI testing document.
I have done...
Hello,
I've been using https://github.com/NordicSemiconductor/pc-nrfutil for few years now as a library of my own application to do DFU of a device. Everything worked and...
I am using an nRF52 DK and running a modified version of the heart rate collector example from the pc-ble-driver-py repository.
My modified program scans for connectable...
If you can expect the data to be sent or received at random times over UART, does it make sense to suspend the UART in the driver? Is it fine to leave both TX and RX enabled...
We are building a device where nRF9160 acts as a master that runs Zephyr OS (using NRF Connect SDK). Our device has a 2nd communication interface beside the nRF9160 modem...
