Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
hey
I have worked on BLE, and learned the BLE protocol stack. Now i am learning BLE Mesh. I found the Mesh is also having a stack, I could not understand why both the stacks...
Hallo,
I request for your time and effort to solve the issue that I am facing at the moment. Any suggestions and solutions are highly appreciated.
Hardware: NRF52840DK...
Hello,
It there a download for the nRF-Command-Line-Tools_10_12_2_Installer_64.exe?
I only see a zip file with this and a python setup. I have an internal program...
Hey, I've a string of less than 10 bytes (10 characters max) and I'm establishing the connection between the Central (nRF52833-DK) and the Peripheral (nRF52810) and I've set...
Hello,
We are trying to use the Cryptocell as used in example nrf_crypto_aes_cbc_with_padding along with Secure DFU. However, when the application loads the crypto engine...
DFU secure bootloader ( secure_bootloader/ pca10040_s132_ble ) using segger embedded studio version 5.50
Am using SDK version 17.0.2 for BMD350 nRF52832 module
Already...
Hi there,
I was able to successfully compile and run the "BLE HIDS keyboard" example on my nRF52832 using Segger SES 5.44
My Nordic chip is connected via UART Rx/Tx to...
Good day
I use NRF52840 + SDK v17.0.2. My application relies on _gls example and mainly copies its security settings ( also uses peer manager ) except I use MITM protection...
Hello Dear!
Please look at the red area in the picture.
The C9 820PF, it's no commonly used,We buy it very hard.
Can i modify C9 820PF to change C9 1 nf in desgin?
I've read quite a few threads where people are asking for help getting NAND Flash to work with their devices, only to find out they are not supported. I see that only NOR...
Hi
I am using nrf52832 to develop a ble hid device with tile function
I merge sample code ble_app_tile to ble_app_hid_keyboard example
I use the advertising_init function...
The firmware crashes when passing the ble_stack_init() when the firmware is download but in debug mode it works fine. The screen shots below shows this event.
We are using...
Hi there,
For my POC test, I need to send a max 255 bytes payload data from a client to one or many servers. I use two nrf52832 DK boards, BLE sdk 17.0 and BLE mesh 5.0...
Hi,
I'm using PWM driver DEMO5 to change the voltage of IOs.Now I need different voltage ranges.
Here is my code:
The voltage will change when button is pushed,but...
