Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I have compiled the example application ncs\v1.4.0\zephyr\samples\boards\nrf\system_off configured for the nRF52dk_nRF52832
This example consumes 450-500uA (SB9 cut)......
Hello Nordic support team,
We are making product relate to battery service.
Tool and SDK: - nRF5_SDK_17.0.2_d674dde
- SEGGER Embedded Studio for ARM Release 4.52c
...
Hi, I am doing some development in nrf52810. where i want to use BUZZER to produce TONES
I am using SDK17.0.2 SES
I want to create tones instead of just beep sound in...
I found a fairly cheap (<$5) FCC certified NRF24 module with 20dBm output power. NiceRF RF2401F20 ( https://www.nicerf.com//product_180_216.html )
The FCC ID is 2AD66-RF2401F20...
Hi,
I would like to know security related libraries available in SDK 17.02.
Libraries that I found
1. Peer manager
2.crypto library
I would like to know is there...
Hi,
I got problem with Implementing the FDS example code as below, which I using is SDK nRF5_SDK_17.0.2, and always got error "FDS_ERR_UNALIGNED_ADDR", Already searched...
nrf5 SDK 15.20
Mesh SDK 3.0.0
nRF52832
Hi,
I am using nRF52832 and mesh stack , i want deliver temperature data through Mesh network.I look and run light-onoff &...
Hi Folks,
I would like to configure an UART RX pin as input GPIO as well as keeping it as dedicated to the UART peripheral.
I would also like to know if I can configure...
Using the current nRF connect v3.6.1 Getting Started Assistant I've managed to get everything installed to the point of using west to install the complete nRF Connect SDK...
This thread discusses the nrf51 devzone.nordicsemi.com/.../current-consumption-when-using-rtc-ppi-and-gpiote It says that the PPI (for nrf51 chip revisions up to rev 3) keeps...
Hi,
What is the used coding scheme in nRF Connect for Mobile when advertising on Coded PHY? Is it S2 or S8?
Should be clarified in the screen below
Thanks,
Lu...
In this PDF: https://infocenter.nordicsemi.com/pdf/nwp_037.pdf
On page 28 it says:
Active components on the PCB cause wideband noise coupling to the antennas. Verify that...
We have designed a board using the nRF9160 SiP and LWM2M. When testing with poor network connection (~ -118dB) we experience a strange behaviour. From monitoring the current...
