Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
May I know what is the difference of three PNs NRF51822-QFAA-R (H0) AND NRF51822-QFAA-R (G0) AND NRF51822-QFAA-R?
How to identy the three PNs? May I know if NRF51822-QFAA...
I am trying to implement a scenario where the system will be sleeping for a mentioned period of time and then wake up and advertise and transfer data over BLE.
I am using...
Again, if the search engine in your documentation were decent, I would probably not need to ask this question here. The answer probably exists, but try an find it not knowing...
Hello Nordic lovers,
Happy Merry Christmas.
In ble_uart code, I'm interfacing the FreeRTOS & twi_sensor code
The program executed without any error.
And it starts...
Dear Members,
How can I wake up the chip without a button
I'm using the example for Ant,
Ant_bsc_rx .
I have disabled the button with :
bsp_init(BSP_INIT_LEDS...
Hello and Merry Christmas,
Trying to get Thingy:91 connected to cloud. But no such luck.
Followed the video, but somethings are shown. Installed latest firmware (SIP modem...
Hello
I have two questions. Your thoughtful response will be appreciated.
1) What's the impact on power consumption with 1 Mbps vs 500 kbps vs 125 kbps for the same amount...
Is there any way to leave the PPK 2 output enabled when I leave the Power Profiler app? If not, then can I submit this as a feature request?
Without this option I have to...
1、Does Nordic 5340 support 1443a protocol；
2、When the chip（5340） is not powered, does NFC function support passive swiping card
3、Can the reading distance of NFC be more...
Hello
I am using the APII described here:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/include/modem/modem_key_mgmt.html
to add keys to the modem...
Why does the nRF9160 Tx power fall far short of the specification? Its seem to be a false claim that the nRF9160 is a 23 dBm device, and rather is a 20 dBm device. In other...
In the flash write example code the very start of main.c has the following lines
The comment says "Use last page in flash". However, what I am guessing from the code itself...
I am trying to use nrf_serial with IRQ. Tx operations just fine but, i can not get any interrupt when a data comes from uart. I am using sdk 14.2 and not using ble.
Hi,
I am using SDK 14.2 and made some changes with serial example in the SDK. It works just fine while debugging but outside of debugging does not work at all.
I have...
