Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Good day,
I am using a DK board with the nRF52832 (pca10040) and I am using a 4 kHz buzzer connected to the gpio 16. I have seen the examples pwm_driver and pwm_library...
Hi, I am using the Nordic nRF52832, with the Segger IDE（Nordic）, and v1.4.0 of theSDK, and would like to know how to enable both LLPM and Multilink.
I am starting from the...
Hi.
I want to ask about the Queued Writes module and the NRF_SDH_BLE_VS_UUID_COUNT. In the example ble_app_uart, in the "services_init(void)" function we initialize the...
Hi,
I'm having difficulties running the secure bootloader example (ble_debug version), it doesn't seem to be advertising or providing any logs.
I'm currently using the...
Hi,
I want to create a fresh project in Keil with nRF SDK as static library included into application. I have created the project, but when I run, the code always stuck...
Hi,
The error I get is as followed:
Output/Debug/Exe/Lesson10_Part3.elf section `.nrf_balloc' will not fit in region `UNPLACED_SECTIONS'
region `UNPLACED_SECTIONS' overflowed...
This is my third and final attempt at getting a custom nRF52 board to appear on my phone as an Adafruit Feather device. I have no issue with the genuine Adafruit hardware...
Hi! We're preparing a medical device and are evaluating nRF5340 chip. We'd like to know when the chip and PDK will be production ready i.e. when Development Kit for nRF5340...
Hi,
One of my customers is applying LWM2M to their target application.
And they are trying to fix LOCAL PORT of LWM2M.
I heard that when end equipment is registered...
Hello
I use nrf52832 and mpu6050. I am trying to obtain values for pitch, roll, and yaw using mpu6050.
I don't know if it's because there's no magnetic sensor, but there...
Hello Everyone,
I recently started using NRF52840 dongle, I am trying to combine USB CDC ACM with Radio TX and RX examples. Individually the codes the running without any...
sd_ble_enable() returned NRF_ERROR_NO_MEM.
when I change this:
NRF_SDH_BLE_GATT_MAX_MTU_SIZE 23 to 247
NRF_SDH_BLE_GAP_DATA_LENGTH 27 to 251
here are turn...
