Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi. I’ve developed a custom device based on nRF9160 and now have a problem of fixing GPS signal. With the same antenna and same conditions sometimes it takes up to 10 minutes...
I've set up a timer which is firing the interrupt correctly. I then set up a second compare and linked it to the PPI to fire the ADC. The idea is to do these a few times per...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
Greetings!
I am using nRF52832 with SDK 16.0.0 and mesh sdk 4.0.0.
Application: light switch client with LPN features added
In one of application, I have to use...
i already done the nrf52840 dongle that already work as beacon when i have tried in nrf beacon apps. i want the same application but now it is transmitting to server/website...
Hi,
I have a low level mcu (128 kbyte flash) connected via UART to the nRF52840.
My current flash usage (text output arm_gcc) is about 256 kbyte + the softdevice.
Since...
I am somewhat of a beginner - I have successfully built and programmed a "Hello World" example on the nRF5340. However I am having trouble building some of the Bluetooth samples...
So I am using the Mesh SDK in version 4.0.0 and 2 nrf52DK boards with some custom software running on the boards, but derived from the light switch examples. The boards work...
We have some prototype boards that work fine when programmed via the debug out on the nRF52 dev kit, but have problems when programmed with this JLink . Programming with both...
Hi Team,
We are using the NRF52832 Board for our development purpose.We need the last RESET condition reason/source and need to store as log in memory for further debugging...
Hello,
I am looking for some tips to speed up a DFU transfer.
I have 2 BLE, I implemented a DFU master in the first one using SDK11.
Transfer duration is about 3mn30s...
Hi, I am trying to do firmware upgrade of nRF91 over BLE using nRF52 on the nRF91-DK or Thingy91 board. They both have nRF91 and nRF52840 chips on them which are connected...
I am currently working on a Heart rate sensor(max30102). I have connected the sensor to my nrf52 DK as follows: GND -> GND VDD -> VIN SCL -> P0.27 SDA -> P0.26 INT -> P0.17...
Hi everyone,
I have lately had some problems with my application which has different characteristics enabled, such as nus, battery service, dfu etc...
The problem I am...