Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hi all,
I am testing the OpenThread connection with 3 nodes at the present,
One is working as End-device with MTD (Minimal Thread Device) firmware others are FTD (Full...
Hi Support Team,
In reading this white paper,Section 3.5 Testing RF performance,
a colleague informed me that a test UICC which is provided by the LTE tester vendor say...
Hi All,
I'm using hci interface to scan the ble based beacons.
While scanning hci interface's Rx bytes keep on increasing because beacons are being scanned.
I'm using...
Dear everyone,
My platform is SDK16 and IDE is KEIL V5.25.
I set timer 2 to 104uS to sample a serial data. It isn't UART data, no start bit and stop bit.The start bytes...
1. Using the nRF Connect SDK v1.2.0 development environment, nrf9160 developer, when testing connections to NRF_CLOUD in China, cannot be connected. 2. Please provide the...
1. Optimization is set to 0 flash read and write errors, set to 3 flash read and write correctly? 2. Please tell me what effect the optimization is on flash reading and writing...
Hi .
I am using nRF52840 dk in windows 10 environment.
I want to measure the RF output power of a single nRF52840 using nRF52840 dk.
I succeeded in generating a...
Hello,
On my custom board, on nrf52832, I can can use app_buttons for all usual pins, but not the XL1 (P0.00). I didn't try XL2 (not routed)
Using this pin as input or...
Hello devzone! I am using translation.
I'm trying various things in a continuation of my previous post , but I do have one question.
I set NRF_LOG_ENABLED to 0 at ble_app_blinky...
I've got an nRF52840 dev kit and am building my code using the app_ble_hrs_freertos project as a starting point. I'm building the .elf file, which I load into Ozone to do...
Hello everyone,
I hope that you are all doing well during those hard times...
I am writing a code for a nRF52840. The connection is successfully established with a cycling...
I have the NRF_CCM peripheral setup to encrypt packets on-the-fly. I can verify packets are properly encrypted when the payload size is 27 bytes or smaller. However, anything...
Hi,
I have created a configuration based on usbd_app_uart example where both usbd and softdevice are enabled on my device as soon as the device is turned on. When I transmit...