Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
hi, my name is tyto I just learned programming about nrf52832, before I used to work with Arduino, after trying to learn nrf52832, it turned out to be very difficult for me...
Hi,
I'am using SDK v15.0.0 with the BLE OTA DFU bootloader. Is there a possibility to access the bootloader start address for a static assert in the application at compile...
We have bought nrf52 832 development kit.
When we checking the kit in nrf52 utility than it detects the IC nrf52 840 .
Hence we have erased all the memory in the DK...
Hi everyone,
I am using the following files to configure uart for laser distance sensor.
Serial Library
I am able to write command to the Laser sensor and also the laser...
Hi,
As far as I understand from this page [https://openthread.io/platforms Host / 802.15.4 Controller section] it is possible to have Dongle running thread attached to PC...
Hi, everyone,
We develope project on nRF52832 Chip. It has one UART port and we need to make it working as RS485. For this purpose we connected to TX/RX pins the required...
I am trying to send hundreds bytes to peripheral, the best tool that I can find, is still nrfConnec. But the data only be typed one by one. Is there any way let it load a...
I am using a nrf52832 with SDK 15.2 and softdevice s132 v6.1
My peripharal should transmit an iBeacon to wake up an application on the smartphone and also transmit a connectable...
Hello,
For a new project I am using the Decawave module DWM1001. This module is equipped with an NRF52832. I have already used the nrf52832 for previous project and I face...
Hi there,
Is there a specific sequence needed to power-up the NRF52840?
Let me get into the details:
My design uses configuration #5 from the datasheet (see below...
Hi, I'm using the serial example from the nRF5 SDK for Mesh (version 2.2.0) and after running it for extended time with data being received from nodes every few seconds, it...
I have a small app_usbd demo which works fine on the nrf52 dongle, but not on the larger nrf52840-dk.
I am running SDK 15.0 with the errata fix mentioned on several other...
ATT MTU THROUGHTPUT EXAMPLE FOR nRF52810 on KEIL using S132 v5.1.0 PLEASE >>>>>>>>>>>>>
Tried this : https://devzone.nordicsemi.com/b/blog/posts/the-s132-v5-1-0-is-now...
