I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
I have seen this forum post: devzone.nordicsemi.com/.../
Which refers to this blog post: devzone.nordicsemi.com/.../
But when I use the Keil Packs Installer, and check...
Hi,
I'm approaching the nRF51 tools for the first time and I'm trying to recompile the source code for the desktop 2 reference kit with Keil 5.14 as a sanity check for...
I am developing an application where a repeater unit connects to a number of other units, gets some info, aggregates it and broadcasts it as a peripheral unit (in a tree structure...
20150424_iPad_iOS(8.1.3)NrdkKS_sniffer.psd
Dear Nordic,
I want to control the volume up feature through HID for iOS while pressing the key.
How can I proceed for...
Greetings,
I have a peripheral (S110) , when it is connecting to a central, it also need to scan another broadcaster (beacon) to obtain its RSSI and send to the central...
I have adopted the S120/S110 multilink example to the following: central.zip and peripheral main.c
I want to send a notification from the central to the peripheral and...
I've developed an application on the nRF51 DK, now for further testing purposes I need to upload it to the nRF Beacon (PCA20006).
My software uses SDK8 (S11 v8) and it...
I want to get rid of the board support package, and write my own code to interface with the least complicated drivers for UART, BLE and SPI etc.
If I remove BSP I ifind...
hi i have pca 10001 eval kit .I need to connect it with PIC16L1947 controller via uart.The data transmitted from pic is to be collected by nrf51822 and it should send as advertisement...
I am developing an application from scratch for the pca10001 by copying a lot of code from the heart rate example.
When calling "softdevice_ble_evt_handler_set" I get an...
I am looking over the stack-up for the dev board which I received from an FAE and has designed in a 50mil width PCB antenna. I am using this online calculator here:
emclab...
Hello--
The nRF51-Dongle has these 20 pads which I think correspond to a debug port:
On the schematic, it looks like these feed into JTAG signals:
My question...
Hello,
I just got a nRF51 DK and I'm trying the examples of nRF folder in the Pack distribution (SDK 7.2).
I can compile the Blinky project but its not working if I...
i have the nRF51DK that comes with the Segger j-link programmer. Can i use the programmer on the board to program a custom board i purchased from Nordic preferred vendor?...
