Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
Hello, I am using W25Q512NW ( https://www.winbond.com/resource-files/W25Q512NW%20RevB%2007192021.pdf) in my custom board. I want to store the sensor data in this flash.
...
Hello,
We have a BLE product using the nRF52840 and nRF Connect SDK. After upgrading our firmware to use nRF Connect v2.6.2 we intermittently get this assert from the SoftDevice...
Hello, I have a BLE Mesh application which is advertising the Mesh Beacon. If after mesh is enabled, I configure and advertisement for showing manufacturer data, the Mesh...
Hello,
Currently, we are using a bootloader on the nRF52832 with the nRF5 SDK, and we are considering migrating to the nRF52811.
We have identified two possible options...
I am using the nrf connect sdk manager to download a tool chain (any version) and they always error out with this error below. I am on WindowsARM 64. I am not sure that matters...
Hello,
I am using the following device and development kit:
Device: NORA-B106-00B (nRF5340)
nRF Connect SDK: 2.0.2
When an interrupt is configured on the GPIO...
Hi, in our project with the nRF5340 we desire use the nRF21540 to have a long conection for BLE, the problem is we don't have any pin free in the nRF5340 to manage the nRF21540...
I have configured new UART in zephyr.dts device tree like this" "/ { chosen { zephyr,console = &uart1; zephyr,shell-uart = &uart1; zephyr,uart-mcumgr = &uart1; zephyr,bt-mon...
my device acts as ble periph ,case BLE_GAP_EVT_DISCONNECTED in ble_evt_handler , if do m_conn_handle = BLE_CONN_HANDLE_INVALID,current changed to 2.5mA, if dont, current is...
Hi,How can I force mcuboot to use a specific serial port for logging?
chosen {
zephyr,uart-mcumgr = & uart0 ;
zephyr,console = & uart1 ;
zephyr,shell-uart = & uart1...
Hi,
we have created a new product prototype where audio streaming is the functionality. 2 different HW revisions were so far built, the software originally is built to use...
I am trying to make the broadcast _audio _sink work . It is always stuck with the following logs :
Broadcast Sink created, waiting for BASE
which then times out with ...
We built a custom version of the Direct Test Mode sample in our firmware, using the USB shell to interface with the test operations and removing the UART or HCI interface...
I have a IMU whose interrupt is connected to GPIO0.11 which is also nrf-gpio-forwarder GPIO (which I dont use)
I managed to get it to work but lost that progress and cant...
