Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hi，
Please help me with this interrupt error
dk:PCA10095 0.11.0
sdk：ncs v1.5.0
example path:D:\ncs\v1.5.0\applications\2_hello_world_timer
example code:
test...
Hello, I have a big problem now. I set up a BLE network with 11 peripheral boards connected to 1 central board via NUS protocol. the peripheral board is based on NRF52840...
We are making a product with nRF51822;Powered by a CR2032 button battery ； Hope to achieve low power consumption;
It can be seen in the datasheet that nRF51822 has Internal...
I've been checking the nRF52805 Errata document to see which errata apply to our product and do not yet have a workaround implemented in our firmware.
Unfortunately, I'm...
Hi,
Device FW information is as follows: SoftDevice: s113_nrf52_7.0.1_softdevice.hex bootloader: mesh_bootloader_serial_gccarmemb_nrf52832_xxAA.hex device page: device_page_nrf52832_xxAA_s113_7...
I want to use our app in phone to communicate a nrf5340 board through ble. my project use sample peripheral_uart . but app ble three 128 bit UUID is different from ncs1.5...
Hi,
I'm trying to measure and log the low power coming from a peltier module. (TEG seebeck effect). In Ampere meter mode with LED for load I get nothing. Replace TEG with...
Hi,
I successful developed a application using nrf / zephyr SDK and install the applications on the nrf52840dk and dongle. Now I want to adjust the power using
CONFIG_BT_CTLR_TX_PWR_PLUS_3...
hello i am trying to interface RN8209c ic with nrf52832 using uart communication with sdk 15.2
uint8_t readbuf[50];
uint32_t err_code;
uint8_t buf[10]; buf[0]=0x7f;...
Hi,
I am trying to modify the Android nRF Mesh app to filter un-provisioned devices with URI hash contained on un-provisioned device beacon.
My question is how I can...
Hi
I have a question, the Nordic SDK have a DFU, I want to know what is the default value of TX power in Bootloader? Can we change the TX power? if yes. How to change it...
Hello, I'm using nrf52805. It is confirmed that P0.04 is AIN2 and P0.05 is AIN3. Can I use this pin as UART TX,RX? What should I do to use it? Thank you.
Hi!
I am trying to work through the nRF Connect SDK tutorial series, and I got stuck at the "building with west step" in part1.
When I try to build my project using the...
