In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Firstly, I am a very beginner in the BLE domain. I have very little knowledge of it.
I want to do a project where multiple BLE peripheral devices(nRF52) will communicate...
Hello:
I have questions about eSIM card.
As we know, GSMA standard eSIM card is an empty chip, we can use eSIM card after ISP information is installed into eSIM card....
Hello,
I have the same question as mentioned in this article:
https://devzone.nordicsemi.com/f/nordic-q-a/19252/how-to-avoid-interrupt-handling-is-not-missed-with-sd_app_evt_wait...
Hi,
I use nrf sniffer to monitor BLE communication. After pairing with encryption, wireshark indicates Encrypted packet decrypted incorrectly (bad MIC).
I think there...
I configured Uart on 23 - Rx and 24 - Tx of NRF52832.
In simple uart example it works fine with uart_event_handle for rx.
But when this code is merged with Nrf Mesh Dimmer...
Hi,
Having gone through the nRF52832 datasheet, the only discernible drawbacks of moving from an external crystal to synthesizing the Low frequency clock from the high-frequency...
On the Nordic Semiconductor infocenter , 12 reference designs for the nRF52840 are given, 6 for the big QIAA chip and 6 for the small CKAA chip. However the reference designs...
Hi
We are developing the use of ESB together with BLE, using the Timeslot API.
We have been using the known tutorial for the ESB timeslot implementation:
https://devzone...
Hi,
We are using nRF52832(lairdBL652) module for indoor application for the prototype version.
We are using nrf52832 for both central and Beacon device.
We have made...
Hi,
I have combined the light switch and the dimming example. The thingy 52 contains one generic onoff server and two generic level server for brightness and colour.
The...
I updated Thingy91 with modem firmware (mfwnrf9160100.zip) and application firmware (thingy91_ltem_v0.2.2.hex) from latest firmware package (thingy91fwv022.zip).
Question...
Hi,
I have nRF9160 DK. I downloaded nRFConnect SDK with source code.
I know that samples compiled with libraries are loaded and executed under MCU on the DK board. Since...
I only want to dfu for bootloader ,but i have some problem ( insufficient resource、 dfu success but my device is crash ).
maybe my bootloader.zip flie is error.
can you...
Hi guys,
I am using mesh server example with UART fuctions integrated into it.
I wanted to send a string through UART.
I tried using app_uart_put() function and this...
Hello,
I was wondering when a device needs to be certified and if that is a country by country basis? If you were to follow the circuit guide lines, would you still need...
