Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
I'm running the Nordic/Thread SDK 3.2 with an NRF52840 (Rigado BMD-340) on SES 4.42.
I've got a project using BLE + Thread and I'm having problems implementing a hardware...
A multiperipheral connection to a central, all with custom nordic devices (nRF52840) has been stablished. Comunication and connection work just fine, but after a synchronization...
Hi ! I am represnting company responsible for fruitymesh ( https://github.com/mwaylabs/fruitymesh ) which is an open-source proprietary ble mesh running on nrf5 chips. For...
Dear Support,
I have adjusted the radio test example in SDK16.0 for my custom hardware application using the nRF52840. I have followed the instructions on this page to...
To the kind attention of Nordic support team,
As it was said https://devzone.nordicsemi.com/f/nordic-q-a/57531/sdk16-nrf52810-secured-gazell-keil
the secured gzll library...
Hello,
I'm able to program the code (below) to the nRF52 DK. Leds 17 & 18 are working.
I'm unable to program the code to my custom board. Leds 9 & 10 are not working ...
Is there any problem with beacon advertisment and ADC? I have 3 adc pins configured to measure three different sensors... When i use UART over BLE... everything is ok.. but...
Hi!
I seen video and read manual how to use it, but still not doesn't work.
PPK + PCA10040
on the PPK board I set jumprs to DK (all 3 pcs). USB connected to PCA10040...
Looking through the datasheet, current consumption is provided for the nRF9160 Modem at 3.0V and 3.5V. Is it possible to get information on 5V related current draws? I've...
Hi,
I am using the example nrf5-ble-mpu-simple from nrf5-mpu-examples-master to do the following:
a) send a BLE beacon advertisement (non connectable)
b) periodically...
We are currently having an issue with DFU failing on Samsung A7 a running andorid 6.0.1. We are using nRF Toolbox for BLE (DFU application) and when I try to connect the device...
Good day!
I'm working on Time model fro Bluetooth specification.
Question is about time handler. I can't figure out should I write a separate handler for TAI, or I should...
Hi!
I´m currently using the nRF52840 demo board to determine the bluetooth range of the device I'm working on.
The question is: which is the orientation of the antenna...
