I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
Due to resource exhaustion I'm curious whether this is possible.
It violates the 1-1 GPIOTE rule and I couldn't find any thread/message about it being possible or otherwise...
Hi,
Our customer needs to test the RF performance of nRF7000, please provide the test documents, test tools, and test procedures, as well as relevant information about WIFI...
i have small applications which can comfortably fit in as little as 32K of SRAM.... i have no issues with the mechanics of linking my program, as well as copying code from...
Hello,
I have a problem with my DK. Everytime I try to plug it in the USB C port of my Computer the J-Link OB is the only Chip that wakes up. I cant program the nrf5340...
Hi,
When using RTT for debugging on the nRF5340, after every flash i have to press the following button:
Then every time i get presented with the following dialog...
I would like to ensure that a particular GPIO pin is disconnected when an nRF52840 is powered up via the initial configuration specified in the DeviceTree board overlay file...
I get the following error when clicking flash button in nrfConnect VS Code extension with an nRF54L15 DK:
Error: One or more batch tasks failed: * 1057701224: Device error...
Dear Support Team!
I'm just about to flash an external board (nRF52820) through P19 where the MCU is powered at 2.3V. I would like to use the nRF52833_DK and the PPK2 to...
Hi Team,
We are using SDK 3.1.0 and radio FW version 1.3.7.
Trying to read RSSI, RSRP, RSRQ, SNR levels using AT command AT%MEAS but it returnns error.
Am I missing...
Hi Nordic,
I'm developing a BLE protocol on an nRF54L05, and is trying to send (On request or by notifying) up to 750 logs of data, each log being 8 bytes (1 byte event...
Hello everyone,
Im using nrf5340dk for the first time, i have built project for nrf5340dk_cpuapp and i think code is good but for some reasone i dont see a led diodes turnin...
Hello,
I had a question about the BT GATT DM Workqueue used in gatt_dm.c.
In NCS 2.8.0, the BT GATT DM Workqueue was introduced as an alternative to the System Workqueue...
Hi List, I have been successful to run my basic functionalities like GPIOs, I2C and ADC using custom board files for nrf54l15 based custom hardware.
Now, I am trying to...
Description:
Hello, We are developing a DECT NR+ communication setup using multiple nRF9161 DK boards arranged in a Sink–Relay–Leaf topology.
Each board operates as a...
