We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi Team,
For my project, I am using nRF 5340 board and using the Zephyr SDK for development. I need to read and write data from/to an external SPI EEPROM used ( MP95P08...
Hi,Team,
I am currently using the nrf54l15-dk to debug NSIB. The version of my NCS is v3.0.2. I referred to this link: https://docs.nordicsemi.com/bundle/ncs-2.9.0/page...
Hi,
We have sent out our product (includes the nRF9160 SiP and an nRF52840) for EMC testing and the test lab is asking for the following:
nRF9160 LTE Cat M1 and NB...
I am trying to set the charge current (ICHG) to 100mA or 200mA using nPM1300 on nRF52832 via TWI (I2C). However, the measured current is always limited to ~87mA, even when...
Dear Nordic Support Team,
I am currently working with the nRF9160 and exploring secure methods to lock and unlock the device without losing the firmware.
At present, I...
Following the instructions from
https://docs.nordicsemi.com/bundle/asset-tracker-template-latest/page/common/getting_started.html
I get build errors building the asset...
Hello Team,
We are currently working on the nRF54L15 platform and using nRF Connect SDK v3.0.2. We've successfully added support for DFU over BLE using the following steps...
Hi, I am working on a project where ECG data can be send wirelessly. For that I am using ADS1298 and nRF52833. I am very new to it. I have connected the nRF52833 SPI lines...
Hello all,
I'm using nRF5_SDK_17.1.0_ddde560
Examples folder:
...\nRF5_SDK_17.1.0_ddde560\examples\peripheral\twi_sensor
...\ble_peripheral\ble_app_blinky
Are...
Hi, I created a blinky sample for the ProMicro board. Entered the flash mode as mentioned in https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/boards/others/promicro_nrf52840...
Hello ,Nordic
Our product uses the Nordic nRF52832 chip, and we recently encountered a device with an anomaly related to FDS writes to Flash. We are using nRF5 SDK version...
I am using NRF SDK 17.1.0
I inherited some legacy code that was a mess, and rewrote it.
Part 1 -
First I skipped the peer manager thinking it was not necessary. Then...
I am debugging my custom nrf54L15 board, and want to use the nrf54L15-DK to flash and debug the board. My SWD debug probe and cabling was used for a previous version of the...
For VDD-nRF in the nRF54L15-DK schematic When I check the schematic, I can't tell which part is internally generated.
When I check the actual board, VDDM_nRF and VDD_nRF...
