Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi
Try to enable reset pin on a 52810 custom board
After defining CONFIG_GPIO_AS_PINRESET in project I ended with UICR registers set to 0 both PSELRESET[0] and PSELRESET...
I have a project with app + SD + BL + Settings page, all merged using the mergehex tool
The mergehex was installed as part of the nrfutil package.
all is well when the...
Hello,
I'm using sprintf to prepare a string to be sent with app_usbd_cdc_acm_write() with a usb configuration resembling your usbd_cdc_acm example of SDK 17.0.2.
When...
Hi everyone,
I want to serial print an array of bytes in hex format. The array size is 200bytes. I tried to use the NRF_LOG_HEXDUMP_INFO but it doesn't print all the array...
Dears,
Diagram as attached, we want to make a audio recorder design.
Customer wants to recorder the audio, and at the same time do audio player works.
Is it possible...
I'm evaluating nRF52840 DK.
Currently running peripheral_lbs example.
I'm trying to set security level to BT_SECURITY_L4
I'm connecting to nRF52840DK with via smartphone...
Hi,
I'm using the nRF5340 DK and SES 5.34a, nRF Connect SDK v1.4.2. For python, I use pyenv virtual environment for which python is set to 3.9.1.
I am able to build and...
Hello I have a question. After when I have used saadc, the consumption increases by 0.9mA. And stays it so. Do you have any idea, how to find out what it does?
saadc init...
Hello,
I'm using a nRF52832 chip and attempting to broadcast a public MAC address through the application. I'm observing that the device broadcasts MAC Address FF:FF:FF...
Hi.
I am building my application on top of ble_app_uart__saadc_timer_driven__scan_mode example.
I want to interface an i2c device with it. The i2c device works perfectly...
Aim:- To read temperature and humidity over a mesh network and display it in an android application
Devices to be connected in Mesh :-
nRfF52840 Development Kit x2 ...
Hello,
I am currently working with nrf 52840, using segger embedded studio (V5.34) and SDK 17.0.2.
For some reason, when I open any example under ble_peripheral, such...
Hi,
I installed nRF Connect SDK v1.4.2 by the tool chain manager and was following the Getting Start guide and entered here.
https://developer.nordicsemi.com/nRF_Connect_SDK...
