Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
There seems to be a blanket statement of v5.1 compliance here:
https://www.nordicsemi.com/Software-and-tools/Software/S140/Download#infotabs
Does this apply to all revisions...
Hello, when will the v8.0.0 version of the SD for the nrf52840 be available? It seems to be listed in the SIG webpage, but not available for download on the nordic webpage...
Hi,
While trying to measure timings with input captures and pin interrupts, I noticed that the SDK-provided pin changed event is very slow : by the time my handler starts...
I am trying to port my working application from a nrf52811/s112 to nrf52832/s132, both with SDK 16.0.0. I'm at the end at the process, it builds fine on nrf52932, I just can...
I'm new to develop firmware on nRF9160-DK, and my first target to add APN to use LTE-M.
For now, I'd like to do a simple way in the below even this is temporary.
=> Hard...
Hello,
I try to transfer the thread_mqtt_sn_client_publisher example from the pca10056 to the pca10059.
Before that, I tried out the example with the pca10056, a boarder...
Hello! me and a coworker are developing a library for communicating with a peripheral via UART. The main idea is that when we send a command, we should get the corresponding...
Hello Team,
I am new to the OTA process for nRF52840. Please help me with the below query.
1) Is it possible to perform the OTA over BLE and over thread network as well...
Hi, We use the QSPI already very well for a flash device that has the correct commands. Now we want to use a SRAM, also QSPI prepared, but it has some other commands, there...
I'm trying to decide on a protocol to use between two nRF52840s.
Both will connect to an App and each other at the same time
Latency is important because the communication...
Hello everyone,
I'm currently trying to get a SiLabs WF200 WIFI module working with a nRF9160 as the host running on Zephyr. Unfortunately I do not get any clock signal...
Hi,
I am testing the advertisement packet scanner based from nRF5_SDK_17.0.2_d674dde\examples\ble_central\ble_app_uart_c.
At current stage, I can receive the advertisement...
I want to use bootloader for nRF52811.
On nRF5 SDK 17,
exmaples/dfu/secure_bootloader/pca10056e_s112_ble/config/sdk_config.h #define NRF_DFU_APP_DATA_AREA_SIZE 8192
...
I am writing a basic health device application, It starts, loads saved data, starts advertising, takes measurements, if a connection occurs the data is transferred, other...
