Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi! I want to copy data from internal flash to a statically allocated buffer in RAM. I get a DACCVIOL hard fault try to do this by memcpy. The hard fault depends on the number...
I need to send 5 sensor values received over SPI to an app over BLE about 5 times a second. I also need to send a few configuration parameters from the app back to the nrf52...
I am using nRF 52 DK connected to Arietta with ARM Linux (4.2.6) 32 bit.
when I was trying to install "vcpkg" using "./bootstrap-vcpkg.sh", I am getting some errors as shown...
I have a phone app which talks to my peripheral device running the nrf52832 and so I will eventually add another peripheral device which ideally can communicate directly to...
Hello everyone!
I'm working on a project where there are 2 microcontrollers: the Nordic nrf52832 and a 3rd-party uC (can't disclose it). A protocol to transfer the firmware...
I feel confused about bearer. what's the difference between mesh-bases bearer and PB-ADV bearer or PB-GATT? there is little knowledge about mesh-bases bearer within mesh profile...
Good afternoon,
At the place I'm working there's 2 main projects using the nordic SDK, while one runs on the 12.3 version, the other is very outdated and still runs on...
Hi,
I'm having a problem at the moment with code based on Espruino on nrf52.
I connect as follows:
ble_gap_scan_params_t m_scan_param;
memset(&m_scan_param, 0,...
I've seen a few post that have similar issues but none that solve my problem.
I have two uarts (uarte0 and uarte1).
I disable them before going to sleep.
I wake with...
Hello,
I cannot successfully flash an nRF9160-Dk to a usable AT modem state using a brand new install of nRFConnect on Windows10, following this Blog post guidance - https...
I am working on 802.15.4 using nrf52840 and sdk 15.2. I want the receiver node to scan the network for beacons transmitted by the transmitter node for 100ms, go to sleep for...
So its seems nrf9160 docs recommend having VDD_GPIO only at 1.8v ... that running at 3.0v (or 3.3v) will compromise LTE performace.
I have 3.3v rail and 3.3v SPI device...
Hi Folks,
I'm trying to use the Power Profiler Kit. Unfortunately I keep getting 'Failed to start the PPK'. I've updated the drivers (and can program the nrf52832 DK with...
In the nRF52840 Product Specification v1.1 ( HTML ) , description of the QDEC peripheral, Table 77 on page 275 ( direct content link) , it appears to indicate that the LED...
