I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hey guys,
I have followed this tutorial that shows how to modify advertising data, and more particularly the name.
What I want to do is set a name in the beacon example...
I've added a HID service in my project.
I see a lot of messages
<00> debug> nrf_sdh_ble: BLE event: 0x57.
in the RTT Viewer.
What does the event 0x57 mean?
Hello All,
We are designing a product based on Tracking device, for this we use nRF9160 module & use controller #nRF52840 to send AT command for LTE and GPS.
We do not...
I'm trying to track down an issue where our application gets stuck due to what looks like an infinite loop in the app_timer2 timer list. When it occurs we see the next pointer...
Hello,
I'm using a custom board with nrf52 using sdk12.1 and SD132 v3.0.0. and the nordic's nus peripheral service.
I am able able to read and send data without any...
Hi,
I had a building project until I added app_uart_fifo.c. The app fifo and uart flags are enabled in the sdk_config.h. This is a custom board. Now when I build I get the...
Hi, I'm building a BLE peripheral with one button only. The button exposed over bluetooth. Obviously, the button handling module (GPIOTE) is used. After advertisement timeout...
Hi,
I am want to do wake up on motion when any threshold value generated by icm 20948 accelerometer I want to send an interrupt from icm 20948 to nrf52832 to wake up from...
Hi !
I'm using the nrf52832 with SDK 11 as pheripheral.
In Android phone the bonding and the scan request working great with my unit !
However, in IOS
1) i do scan...
Hello,
I am working with LPN example of SDK 3.1.0. In the example I need to change the poll interval time based on our application requirement.
I looked at this equation...
Hi Nordic team,
I have a curious problem I need a little help with:
(NRF52840 & SDK 15.3)
I have a project which is an integration of the ble_uart example and the serial_uartes...
I have searched your forum and have found several references to my issue; however, I have not been able to get anything resolved.
I am using the nRF51822 which is part of...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image. I am using ‘ble_app_blinky’.
I have gone through “Application Timer” tutorial...
I have a development board and load the client central BLE blinky to it, then the peripheral BLE blinky to my custom board and power up and the central development board stays...
I was wondering if it is possible to do HTTP requests with the nRF9160 just by using AT commands? Since this is usually possible with such kind of modules.
The reason is...
