Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
I am running nrf5340_audio_applications on the nRF5340 Audio DK. Follow the requirements, i add an external flash shield. I've only changed
the configuration of flash and...
Hello, I am trying to flash the nRF52840 SoC on the nRF52840 DK using an external J-Link debugger, without relying on the interface MCU or the onboard J-Link. My current switch...
Dear Nordic Engineers
I used NCS2.9.0 to develop a device based on nRF52840 and I would like to use UART to DFU the device based on SMP.
Now, I test SMP samples and use...
Hi,
After the latest update, the below setting allowing me to select nrfjprog as my device provider is now gone:
I am using the nRF Playground Docker container...
Hi,
I have been using NUS code to stream data between mobile and nrf5340 audio dk. is it possible to stream 256KB of data at a go? what is the maximum MTU size that i can...
I am using nrf connect sdk 2.7.0 with nrf52811.
My application is based on nrf5-sdk V 17.1.0 but now i want to port it to nrf-conneck sdk 2.7.0.
I want to know whether...
I have a problem with the package with nrf5 sdk, there for pca10100 examples are not there. i am trying to interface quadrature decoder with one encoder and it is not able...
Hello,I have a custom board using a Nordic nrf52823 microcontroller on it. I am using VSCode with the nrf connect SDK and the Zpehry RTOS- I want to make use Zephyr RTC to...
Is there any relevant assessment or introduction document of IC FMEA?
For example, the impact of abnormal short circuit and ordinary short circuit on chip 52832;
And...
1、I used the spi_bitbang routine to port it to the network core to run, and after the program was burned, I used an oscilloscope to measure the CLK pin waveform and there...
Hi,i I am testing the sample(ncs\v2.7.0\zephyr\samples\drivers\spi_bitbang) at a 52840DK board, with overlay setup like these:
spibb0: spibb0 {
compatible = "zephyr...
Hi nRF support team,
I am trying to add a new Custom Service and Characteristic an application on nRF82540 development kit using the nRF Connect SDK.
Can you please let...
Hello.
1. The nPM1300 PS v1.1 states in Section 6.1.1 the fllowing: "The default current limit is IBUS100MA (100 mA)". But the values after reset in registers VBUSINILIMSTARTUP...
I have finally got FOTA working with external flash, but I have a strange problem.
When the FOTA is complete, the mcuboot fails, but the new image boots correctly.
So...
