Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi,
I have been testing out the channel sounding feature on the NRF54L15. Each device has a bias (difference between the readings and the actual distance) and I was trying...
1. Can we use SIM other than iBasis to use nrf cloud?
2. My SIM does not have a PUK. How to proceed without entering it.
3. We need SIM too kit document for nrf9161. ...
We have a custom board that I ran through the board_v1_to_v2.py program and then attempted to build under SDK and Toolchain 2.8. When I run it it failed in the CMakeLists...
Hi, I'm trying to implement a watchdog on the nRF54L15. I configured the watchdog with a maximum window of 1000 ms, and I'm feeding it from a low-priority thread every 500...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hi,
I'm currently using the nrf52840 SDK board and based on ncs 2.9.0 SDK. I need to make a simple sample customer bootloader that does not use the DFU and MCUBOOT functions...
board : nRF5340
sdk-nrf : v2.7.99-cs2
Zephyr version: 3.6.99
I am following https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/bootloaders_dfu/qspi_xip_split_image...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi,
I'm trying to send HTTPS commands (GET/POST) using the nRF9151-DK.
I’ve already completed the process using nRF Connect for Desktop . The device was recognized correctly...
Hi guys,
For a client of mine I'm working on an openthread RCP implementation using a SolidRun N8 that contains the NRF52833.
I'm using ncs v2.9.0-nRF54H20-1.
The problem...
Hi, I’m working with an nRF52840 DK and trying to use two UARTs simultaneously. I’ve configured UART1 for debugging (console and shell output) and want to use the default...
Hello, I am trying to use the subghz template in ncs 2.5.2 but I am running into an issue when enabling NanoPB. When enabling NanoPB with CONFIG_NANOPB=y the application faults...
I have noticed that Matter V1.4.1 has been supported from NCS V 3.0.0( https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/protocols/matter/index.html ), but I have not...