I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
Hello,
I'm currently using the nRF9151-DK hardware to develop our product based on the nRF9151 SiP . We selected the ncs-serial-modem firmware, and the modem is controlled...
I am implementing the code for nrf54l15 nordic MCU to: Use vbat_mon pin p1.10 in NRF54L15 as ADC and trying to read the voltages, but physically i am not able to read/get...
Hi,
I'm using nrf54l15 SOC with Zephyr NCS SDK to build a BLE application. I want to set the radio Tx Power to be set to as high as possible as our device will be enclosed...
Hi There.
I been 15 year experience in embedded system development but I'm very new to the Nordic nrf environment.
I'm eager to learn and develop some product and provide...
Hi, I have a nrf54H20 board rev 0.9.2 and I followed the https://docs.nordicsemi.com/bundle/ncs-3.0.0/page/nrf/app_dev/device_guides/nrf54h/ug_nrf54h20_gs.html#nrf54h20_dk_bring...
Hello, We are currently working on designing a CS-based distance estimation algorithm, referencing the two example routines, `ras_initiator` and `ras_reflector`, from NCS...
I'm getting exactly the same as this ticket now I've switched to extended advertising. Was there any resolution?
Android is fine, iOS 18.5 phone sits in a connect/error...
I'm testing the spi communication protocol with the nRF54L15 DK. At that moment, I'm testing the lesson5-exercise 1 solution of the intermediate course. The problem appears...
Hello,
As the title, I'm using nRF5340 audio sample to test Walkie Talkie demo.
I know that in nRF5340 audio DK, the microphone is set through CS47L63. Now I want to use...
Problem originally due to installation and failure of Gas Smart meter - a common problem in the UK with up to 4+million similar customers. Issue is Smart meters on external...
It isn't clear from the nRF5340 documentation and the only related post doesn't answer it but if we want +3 dBm output power, do we need to wire the nRF5340 in high voltage...
I have a mouse that is advertising, and I paired it with my host. It always stays in connected mode. When I press the three buttons — middle, left, and right — for 5 seconds...
What is the recommended termination for unused RF pins on the nRF54L15 in QFN48 (QFAA) package? Can you confirm this is acceptable?
ANT Pin 31, floating VSS_PA Pin 32, grounded...
Hi, I want to change the voltage of the VDDIO in the group of pins labelled Port 1. I launched Board Configurator from nRF Connect for Desktop but it says "This development...
