Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi, I'm looking for clarification whether the DECT NR+ modem firmware supports GNSS. Legacy docs say it doesn't, but there is no mention of it in current docs. Based on that...
Hi,
Issue
With the official nRF21540-EK + nRF54L15DK setup, my app/config works: advertising, connections, and PA/LNA behavior are all OK.
On my custom PCB ...
I am attempting to do channel sounding with one initiator and two reflectors. Switching between reflectors, by connecting to each in turn, does work, but it is very slow....
Hi Support Team
The attachment is ANT+ Device Profile for Bike Radar, it mentioned that an ANT+ Bike Light and Bike Radar Sensor can be combined as a single device, but...
Hello,
For a project with nRF9151 as the main microcontroller, we use nPM1300 for power management.
As I understand, for nRF9151, VDD voltage should be supplied prior...
I am developing a simple ble peripheral device that will measure temperature and humidity. For the most
part, it's working but I can't get the behavior I expect when enabling...
I'm a new software developer and I'm not a native English speaker. I ask questions through a translator now, the description might not be clear.
I am currently working on...
Hello,
I would like to know how to disable the NFC function with nRF SDK 3.1.0
I would build the Matter thermostat sample. I tried this: `CONFIG_CHIP_NFC_COMMISSIONING...
Hello,
I am trying to read the MCUBootloader version from the NS (TFM) application. I am able to read it in the Secure application using the fw_info_find function in this...
Hello,
I’m trying to run **LVGL 9.3** on a **nRF52840 DK** with a **2.8" ILI9341 TFT display (SPI)** using **NCS v3.1.0 / Zephyr 4.1 / Toolchain v3.1.0** .
### Problem...
Hello, I want to check the component alignment on the layout.
My layout is different than the reference.
Where should I connect the VNA?
Can I calibrate it on the PCB?
Hi,
I am using a custom nRF9160 board with the nRF7002 Wi-Fi chip via SPI, running NCS v2.9.2 . My goal is to connect to a Wi-Fi network.
However, during initialization...
I want to change the start address of the app in the ESB example from nCS 3.0.2. By default, after compiling and flashing, the program runs from address 0x0. I want to change...
Hi Nordic,
I try to print hello world from promicro(nrf52840).
I am sure board is ok, because I test zephyr 4.2 cdc_acm example on it, and I can see /dev/ttyACM* & console...
