Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi Nordic Semiconductor!
Over the years I've been using your development kits, some days ago I got the nRF5340-DK and started on a new computer. Normally I dive into the...
I don't know why, but after issuing the nrfutil dfu command line, it takes ~34 seconds before the DFU starts and the progress bar is shown.
Sample command lines:
nrfutil...
Hello,
I want to use a FIFO. I want to send the data from file1.c and receive it on file2.c.
Currently, I have defiend my_fifo using K_FIFO_DEFINE(my_fifo) and using...
I am currently working on AoA direction finding solutons, and I have successfully run the demo direction_finding_connectionless_rx and direction_finding_connectionless_tx...
Hello,
I would like to ask you if there is an antenna layout available for the nRF52833. Indeed, I would like to develop my own application with it and, this SoC needs to...
Hello all,
I am currently working on receiving SAADC data and transmitting it through BLE with a sampling frequency of 1kHZ or higher. I am using nRF52832 board with the...
Hello, I have custom BLE service and characteristic as below image.
I wanted to discover them in ble central mode. I have modified ble_hrc_c.c to validate but central...
dear all
When I use QSPI to operate external flash and mount a FatFs file system, when I use RC = FS_ open(&file, fname, FS_ O_ CREATE | FS_ O_ WRITE); When creating a file...
Hello DevZone,
For my project I have a number of pins generating interrupts from different sensors.
I've read that GPIOTE IN events consume a bit more current than the...
nrf_mesh_config_app.h at the generic level mesh example contains constants like DEVICE_COMPANY_ID, DEVICE_PRODUCT_ID and DEVICE_VERSION_ID . I've expected those values to...
I try to build your an example Smart Remote 3 nRF52 v1.2 in Keil v5.34 and I have some errors.
In the case of nRF52832_xxAA (Target: PCA63519-SR3_nRF52832_Shield) I have...
Hi,
I'm a beginner trying to understand BLE extended advertising. I have modified the peripheral/ble_app_beacon example to broadcast extended advertising packets with PHY...
Hi,
I am transmiting extended advertising packets and I want to set the flags on the extended header as specified on the bluetooth core specification (v5.3) page 2691 (photo...
