Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'm measuring the power consumption of the BLE Beacon example and got the graph below for one beacon transmission. I'm wondering what those smaller peaks are with 1ms period...
Howdy,
I'm evaluating the nRF Sniffer + nRF52840 dongle as a stop gap BLE sniffer solution, but I'm having a lot of issues setting it up.
Re: Installing nRF Sniffer (...
Good morning,
I am working with the AOA module of the nRF Connect SDK. I have been able to configure and program the transmitter with the CTE as well as the receiver and...
Dear Nordic,
we are developing an application based on SDK 17.0.2, it user FreeRTOS and BLE with Peer Manager.
We need to store few data in FLASH without confict with...
Hi
We are trying to get the DTM mode working for the NRF52 2nd BLE for testing BLE TX power and RSSI at the factory.
(1)HW setup is shown
(2 ) Procedure
We have...
Hello,
what are necessary that a Device automatically (without a 3rd party app) connect to the GATT Server with a HID Service.
I have implement a
HID Service,
Device...
hi，
I'm use nRF52840 to developing a Computer Keyboard，i wish 8X18 matrix a total of 144 buttons，About keyboard button matrix, please help to determine which GPIO can do...
Hello,
I am trying to resolve some compliance issues with the third-party libraries that are used in the SDK. For nanopb, it seems like the changes in pb_decode.h mentioned...
Hello,
I want to configure pin 0.13 as a rising edge interrupt.
Is there any sample code to configure the pin and interrupt handler?
Thanks in advance.
Hello,
In a previous post I asked about scanning and connecting based on specific advertised data. After some testing I realized that my two nrf dks only connect sometimes...
Hello; We want to use the GPS peripheral of nRF9160. Qorvo QM14501SR LNA is used in your evaluation board. QM14501SR is expensive for our project. Can we use LNA without band...
Hi,
i am working on nrf52832 . i am facing advertising issue with custom board. controller advertise only when i touch 32.786kHz crystals or two capacitors with my finger...
Hi,
I use example projects Thread: CoAP Client and Thread: CoAP Server . I can send and receive data over CoAP. My purpose is to use CoAP, CoAPS and UDP tohether. If client...
nrf_ringbuf has a bug which happens when mixing nrf_ringbuf_cpy_put() with nrf_ringbuf_alloc() and nrf_ringbuf_put(). After copying data with nrf_ringbuf_cpy_put() a later...
