Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
My product uses the nrf52840 chip with NCS 2.7 and has a USB mass storage function.
I would like to implement a feature as below
1. When the USB is connected to...
As the title suggests, I am trying to run the peripheral LBS example on my custom PCB to test BLE before continuing with my application. I'm using NCS V2.9.0. I have created...
I've got an NCS v2.6.1 project on the nRF52832 running a timing chain using PPI for PWM instance 2:
The output of nrfx_pwm_task_address_get is 0x40022008 as I'd expect...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hello,
I am planning to start working on a Dual Find My (Apple + Google) tracker device. We have chosen nRF54L15 to be used for this.
Please provide a confirmation...
Dears,
I have tried to install the nRF connect SW package on a Windows 7 32 bit system (different versions) but was not able to get the applications running. When installing...
Hi:
I can't compile the program.
Please tell me the solution.
I used with Toolchain&SDK: 3.0.2&3.0.2; 3.0.0&3.0.0 and 2.8.0&2.8.0.
VS Code Winwdows 11, Processor 11th...
Hi, I'm working on provisioning a Pre-Shared Key (PSK) during manufacturing for an nRF5340 device. The device needs access to the PSK at runtime to generate authentication...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello everyone,
I am currently working on implementing the flash protection feature for the 54L05 chip. My objective is to safeguard the code storage area from unintended...
I get a bunch of errors like undefined reference to `mbedtls_ssl_free', `mbedtls_ssl_get_bytes_avail',`mbedtls_ssl_config_free', 'mbedtls_ssl_read'
`mbedtls_ssl_set_bio...
