We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I have MCU boot running successfully in my project using NCS 2.8.0 and sysbuild. I'm now trying to add hardware downgrade protection as described here:
https://docs.nordicsemi...
Continue.
PCA100059,S140,custermize periphral Blinky.
I have changed the value transfered between peripheral & center with
uint8_t* data;
uint16_t dataLen;
The max...
Hi,
I'm trying to use device_credentials_installer.py with an FTDI USB-UART cable, but the script returns "No device found." I've tested other scripts and confirmed communication...
Hello everyone,
I'm pretty new with BLE configurations. I'm currently implementing a BLE NUS service, and noticed that on the example code the max length supported is...
Hi Nordic Team and Other,
We are evaluating an audio product using a NRF5340 Audio Dk (Custom Board) and using nrf5340 DK for flashing the custom board using the setup as...
Hi,
We have a pcap file of a MQTTS connection to AWS, provided by the Soracom SIM console. I will print the first lines of the Wireshark trace so you can see what I am working...
Hi, We are evaluating whether nr54L15 supports LE Audio function? According to the specification, it supports bluetooth 6.0 and should support LE Audio (Isochronous channel...
Hi,
currently I am struggeling to get my SD card connected to the 54H20 DK. Each time I try to mount the SD Card I get the following error:
The Error is raised after the...
We are using a custom board design. I created a custom board configuration when using the v2.5 SDK. In this configuration, we have the UART0 pins configured such that RXD...
Hi
I want to use the timer in counter mode (gpio event shortcut to count task). Do you have any number of current consumption? The plan is to have a 64Hz signal but it could...
Hi, after uploading a Zephyr project (like the "Hello World" example), I couldn't see the device in the serial monitor. i add the below commend in overlay file also but still...
Hello,
I am in the process of following a series of tutorial videos on driving an LED with pwm, but I don't understand how to properly configure my .overlay file and my...
Hi,
I am developing an application for an nRF52840 using nRF Connect SDK v2.9.0. The application currently uses the Zephyr driver for simple PWM functions on several GPIOs...
Hello,
I'm using 'nRF Connect for Desktop v4.2.0' and 'nRF Connect SDK v2.3.0' on windows 11.
I was using vs code well for developing nrf52840 board.
But, I found...
