At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
I'm using SDK 7.1, PCA10028 eval board, SD310 2.0.1, MCP 3.6.0.8331
I'm trying to implement bonding. I first initialize pstorage, as a separate call from main. Then I call...
Hello Everyone
i have J link for ARM processor from IAR 2008 module version 6 which specify support for swd, As I checked it on IAR website it support CORTEX-M0 processor...
I use pin SDIN, SCLK, CS, DC.
but how do I connect the pin nrf51822
spi_master_example is
#define SPIM0_SCK_PIN 25u /**< SPI clock GPIO pin number. */
#define SPIM0_MOSI_PIN...
I have been reading about code regions in the nrf reference manual and understood about CLENR0 and how to use it. I have however, two questions
What is Pre Programmed...
I am using the SPI Slave port in the nRF51822 and am always transferring 20 bytes. No matter what I do, it seems that the status register in the IRQ says that I got a TX buffer...
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hi,
I need to be able to communicate between two boards via UART. I had a look at the example from Ole provided here: devzone.nordicsemi.com/.../ as well as other references...
Hello,
I am wondering if I can use any 128 bit UUID value.
For example, in the example uart project, Nordic UART Service = 6E400001-B5A3-F393-E0A9-E50E24DCCA9E is used...
If I want to stream samples up to the nRF Toolbox HRM iOS app plot, what is the fastest that I can call ble_hrs_heart_rate_measurement_send in firmware assuming I have nothing...
Hi,
I'm using nRF51822 Development Kit and trying to program softdevice with nRFgo Studio. The file to program is C:/Program Files (x86)/Nordic Semiconductor/nRFgo Studio...
I'm using S110 version 7.1.0, but need a way to validate in general which S110 and which SDK version I have associated with this .uvprojx project.
Much of this stems from...
I'm running the ble_app_beacon_s110_pca10028 example on my NRF51 dongle. The good news is that I see a beacon transmission on my iPhone 6 on this "Pally BLE Scanner" app....
We are developing a new BLE tag product using the nRF51822. We would like to assemble the PCB and battery in a single operation then program the product sometime later. Can...
