At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
When dealing with low power access via NTN (via Skylo), is there any limitation about any particular use of SW?
Like, is Zephyr or other RTOS combinable with the Skylo certified...
I'm trying to flash a XIAO nrf52840 following the instructions for flashing with UF2 but it won't seem to work. After I drag and drop the zephyr.uf2 file in the mounted drive...
Hello. I am trying to implement stable connection between my nordic nrf5340 and Samsung Galaxy Buds3 earbuds. I did it based on ble audio example with two connections (one...
I have a 7002dk dev kit. Currently for evaluating the nrf5340, which will be used in my product. Currently i am trying to evaluate if it is possible to use the nRF5340 USB...
Hi,
I am using two nRF52833 DK and both are connected with nRF21540.I notice that when I have a very high throughput, never stop sending 244 bytes, I will notice that average...
Hi,
I would like to ask about the future plans for Zigbee development, as the current situation is a bit confusing.
From what I’ve observed, Zigbee R22 has been deprecated...
My team recently acquired two NRF24 transceivers to use on our drone project. Personally I've used NRF24 modules before and have successfully paired them with Arduino and...
Hi all,
i just received 2 nRF54L15-DK boards. Both I am not able do program - I tried:
1. nRF Connect for Desktop
* I did not make any change on the board afre unpacking...
I want to use the boards NRF-5340DK or NRF-52840 with the external host for the channel sounding feature. Can we use the feature on the mentioned board? If so, can you please...
I'm trying to send and receive an extended advertisement packet with about 100bytes of payload.
I started with the sample extended_adv example.
I 1st validated that using...
Hello. We are updating firmware to use nrf sdk 2.9.1 (from 2.5.2). Below is my proj.conf, should I expect any breaking changes?
############################
# Stacks...
Hi,
I want to configure the nRF9160's internal flash storage_partition, it has 32KB currently, I want to change it to 100KB. How to do that? Using nrf9160dk_nrf9160_ns.overlay...
As the title suggests, I want to use west build without having to include the BOARD_ROOT parameter.
I have already referred to this link , but the results were not as expected...
Toolchain v2.70, SDK v2.6.1, VS Code, Windows
Code derived from UDP sample works on DK board but fails on custom device.
Device is using DK board configuration, but no...
I have used ADC Channel 6 (P0.30) for voltage measurement using NRF52832. Previously It was working well. Now it is returning an error.
00> [00:00:00.398,345] <err> adc_nrfx_saadc...
