Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Dear All,
I am using UART read write operation along with the system off mode. So, usually nRF9160 chip goes to sleep and wakes up when it receives something on UART and...
Hello Nordic support team,
I'm working with NRF52832 development Kit. I want to transfer our firmware application (OTA-DFU) from nordic central device to nordic peripheral...
Hi, I am trying to get RSSI values using BLE module on nRF52840(pca20035). But I could not see possible way to get the RSSI values on Nordic Thingy91(nRF9160) Please map me...
hi all
i want porting qpc with softdevice. it need set SCB_SYSPRI exception priorities with PRIMASK bit or the BASEPRI register for critical section
can anyone give me...
Hello,
I would like to update an nrf52840 with DFU (usb-serial). On windows I can use nrfutil. But how to proceed if I want to do that from another microcontroller?
Is...
Hi,
I am working with nrf52840 DK and sending real time sensor data to nrf toolbox using ble_uart. I would like to store adc output in flash and then send it over ble uart...
Hi Devzone
I tried to use saadc with 4channels. when I use this without fpu_fft, It prints correct value well.
But, when I insert the fpu_fft and run it, after a while...
Hello
I have a question about SIG certification. As far as I know, to get SIG certified, I need to download the DTM firmware to the board and pass it to the certification...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Dear Community;
I am trying to make an HTTP GET request based on this code . It works fine but I need to adapt that to fit it in my code. I need to pass some arguments...
Hello!
Is there a way to send gps nmea data through ble connection? Almost all gps bluetooth devices use bluetooth classic to send data. The mobile app where I need to get...
Hi,
I need to read the data from the sensor MAXCESS Digital load cell amplifier in which the output we are getting in the form of current ( 4 to 8 mamp) not voltage. can...
Hey guys,
I've been troubled by the this 0x3E issue for almost disappointed to Nordic.
I'm working on a CENTRAL,which is going to connect a headphone with to read some...
Hi i am checking for the Rssi value of the low power node,when i am placing the device in certain feet, it is giving the rssi reading which is approximately matches with others...
