Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
Hey.
I have a problem where the task watchdog times out immediately.
I have taken the samples/basic/task_wdt sample and modified it a bit to simulate what I have in...
The environment setup I'm using is VsCode with the NRF extension. I'm using SDK v2.6.1. When flashing bootloader firmware to my device I get this output on my vs code terminal...
minimal_log % west flash -- west flash: rebuilding [0/4] Performing build step for 'mcuboot_subimage' ninja: no work to do. -- west flash: using runner nrfjprog Using board...
We have fairly regularly observed that the reset reason register gives two reasons for reset: software request and watchdog.
Is it plausible that these bits are genuinely...
Hi,
I am trying to communicate with nPM1300 PMIC board using NRF5340DK. I have made the connections and set up the overlay file as recommended. The I2C write (i2c_write_dt...
I am currently developing software of the nrf9160 and am having trouble with a firmware upgrade. The firmware data is received via UART. All of the functions work as expected...
Hello all,
I am working on a ble application on zephyr. I need to send a notification on a specific characteristic.
If I call bt_gatt_notify from where I want to send...
We're currently using a virtual operator as carrier, so our device is roaming in Finland. It seems that Elisa (24405) is the preferred network, but the data plan is restricted...
Hello, can 2.0nH or 1.8nH inductors be connected instead of the 1.9nH inductors connected to the ANT1 and ANT2 pins shown in the NRF21540 reference circuit?
After getting nrf52 board I've sucessfully recovered it, flashed it with blinky example and I cannot recover it again. I tried doing nrfjprog --recover and nrfjprog --family...
I'm working on a custom board that uses an NRF52840, I've followed the Nordic Developer Academy course related to DFU over uart0 ( Exercise 1 - DFU over UART - Nordic Developer...
Hello everyone,
I have a custom board with a nRF5340 on it that is used as a BLE reader for mobile phones. Now we wanted to do some EMC testing. For this we need to broadcast...
I am developing a board with the nrf5340, and using a PDM microphone for audio input.
I have used the same microphone on the nrf52832 with the nrf PDM driver with success...
Hello Nordic team!
I'm currently trying to get a demo of zephyr's Blink up and running on my Thingy53 device so I have an understanding of how the connections between...
Hello,
I’m working on an nRF5340 project and trying to measure power consumption in low power mode using SDK v2.6.1. I followed the instructions provided on your website...
