But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello
In our application (NRF52840, softdevice S140 v7.3.0, master device with multiple connections) we are experiencing some strange behaviour related to scheduling of...
Hi All,
I feel like this question/topic has probably been discussed ad nauseum, but I feel like I'm not confident in the conclusion I'm drawing from other posts I've seen...
How to reject/disconnect peer (smartphone) which tried to write huge data to service? For now in my project (based on ble_app_multperipheral project from SDK) if the smartphone...
Hi Nordic Team,
I would like to understand how the radio test works. A better description of the commandos would also be helpful. Is there a more detailed description than...
Good evening,
The following link to "TIMER HAL" lists various enums, including for example " NRF_TIMER_BIT_WIDTH_32 (alias of) = TIMER_BITMODE_BITMODE_32Bit ". I've used...
On Windows 7 64 after update to 3.8 (and 3.9) nRF Connect for Desktop the Bluetooth Low Energy and Power Profiler can't find device nRF52840-Dongle and PPK2.
What to...
Hello,
I was wondering if I could bypass the protocols related to BLE transmission (GATT/ATT) and utilize the RADIO peripheral in a close to constant TX rate without regard...
Hello!
Short question: How can I pass a parameter to a SW Interrupt?
Expanded question: I want the board to wait for an ammount of bytes comming from SPI, once this is...
Hi all,
i am really desperate. since more than 1 week i am trying to work with the digital inputs in my custom pcb.
I can set all digital outputs, but from the inputs...
Hi Nordic support team,
We're using nRF52840 to develop a product with lots of features, using nRF NCS latest version (1.7.x as of writing).
Currently we're sitting at...
Hello! I'm working with the nRF5 SDK17 ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_interactive.html ), and I'm...
Hi nordic,
After I transplanted nrf52832 to nrf52833, the upgrade of nrf52833 failed, or stuck in the bootloader.I tried to use the current method to upgrade nrf52832, it...
Hi
Problem description：
In application serial_lte_modem ,When sending AT command "AT + CFUN?"， return"at_host:Error while processing AT command:",What caused this？Thank...
Hello,
We have a nRF52840 on our board, whose fw we would like to be able to update through both BLE and UART (the MCU is connected to a ST32 MCU via UART) using a bootloader...
Hello Everyone,
I am currently using the AGPS example on the nRF9160-DK with nRF Connect SDK v1.7.0. I notice it requires 4 satellites in order to provide a position fix...
