But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
The lNordic Semi Link
https://www.nordicsemi.com/Products/Development-tools/nRF-Sniffer-for-Bluetooth-LE
mentions that the nRF52840 Dongle can be used as sniffer.
...
I am using:
2x Nrf51422 chips on PCA10028
IAR Embedded Workbench IDE - ARM 9.10.2
nRF5_SDK_12.3.0_d7731ad
I need to transfer a 44 byte payload from one board to the...
I think my nrf SDK toolchain manager missed a tool somehow. When I downloaded v1.6.1 (following the instructions on the website) and tried to build my project using
`west...
Hi, I am testing the flash storage of nrf52840 with NVS example from NCS v1.4.2
i have run the example code successfully. from the example code i have changed the
uint8_t...
Hello,
I am trying to create a single static library for SDK, and use it in application and bootloader, for that i have merged sdk_config.h files of application and bootloader...
Hi there,
We are a cycling accessories company (mainly light accessories) and have been using Nordic chips for BLE 1 to 1 connection of our helmet to phone (for configurations...
Hi,
I have added the bettery service to ble_app_buttonless_dfu_pca10040_s132 project successfully.
The sample code is from latest SDK 17.0.2 .
When I do the same set...
Hey Folks,
The new LPUART (doc here https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.5.0/nrf/drivers/uart_nrf_sw_lpuart.html ) is supposed to address the issue of...
Hi, I am testing " Zigbee OTA Upgrade Server Example with image transfer over BLE ", https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_tz_v3.2.0%2Fzigbee_example_ota_server...
On the device I have flashed the nRF91 with the latest firmware from here: ncs/nrf/applications/asset_tracker_v2. I have flashed the nRF52 firmware with the most recent firmware...
Dear Sir,
I am working on Bootloader of nRF52840 which I need large space to display some LCD when bootloader startup.
I use Keil compiler, SDK 1702.
In Keil, iROM...
Hi,
I'm planning to develope a set of BLE mesh devices (one control unit which is the coordinator and configurator) and sensor devices (low-power, friend and relay nodes...
Hello,
i need a very sample code for ,open a SPI device ad send , receive a byte.
In particular how open the device tree spi device,
how write a byte
how read a byte...
Excuse me：
1、How many low power modes does NRF have?
2、What is the power consumption in various modes?
3、What is the eDRX power consumption(LTE-M and NB-IOT) and average...
