But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi Nordic Team/public users,
Request your assistance for troubleshooting the NDK-nrf52840 board that was having a detection issue whereby my laptop/PC was unable to detect...
Hello, I hope you are safe and well during these times. I have created a successful prototype using the Adafruit Feather nRF52 Bluefruit and the Arduino IDE. I think I am...
Hi,
I want to update the DFU with application nRF Connect (Bluetooth) for beginning I want to try with nRF Example in example/dfu/bootloader_secure. The file secure_dfu_secure_dfu_ble_s130_pca10028_debug...
Hi,
I like to use nRFSDK in my future project, but I don't like the hectic steps to open a project when using nRFConnect SDK. I cannot open Segger IDE directly instead go...
Hi everyone,
Currently, i am working with some zigbee devices using NRF52833 and zigbee SDK 4.1. Now, i want to use BLE DFU with it to update the firmware when needed. ...
I am developing with NCS, but I found only one project "v1.4.99-dev1\nrf\samples\bluetooth\peripheral_lbs" I can add files directly through the option "Add new file to cmakelist...
I m using sdk16.0.0 nrf52-ble-app-uart-c-multilink example. I want to comminication arduino btw BT840F. I try with nrf52840 there is no problem but when i use bt840f i didn...
I'm using a library that does
#ifndef MIN
#define MIN stuff
#endif
Because I'm using segger, I have no control over compilation order, so that's getting loaded first...
I want to design the chip (nRF9160) on our board. 1- What kind of external debug / flash (SWD) can I use to flash the modem firmware and my app?
2- Is there any suitable...
Hello All,
I am implementing a simple UART bridge over BLE and want to add a Characteristic to update the baud rate being used. I thought I added code to support a new characteristic...
Hello!
I have this interesting bug with the twim driver.
It works perfectly with the NRFX_TWIM_XFER_TXRX transfer type: I see the transaction go out on the bus lines...
Hi,
My project uses nRF52840 with SD 140, SDK 17.0.2 and SES. My hardware has SD Card SPI and LCD SPI sharing bus pins, using CS pins to switch devices. Because of this...
Hi,
When I use Texas Instruments CC2650 MODA (using Bluetooth 4.2) as the the transmitter, a smartphone (iPhone or an Android phone) that has nRF Connect app as a receiver...
Are there any examples to program the nrf52 at a lower level bypassing all the bloat/ 10 layers of abstraction in the SDK? TIA.
I often hear that things were more straight...
