We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
A newbie here. I am studying the simple_timer application in the nRF5_SDK_17.0.0_9d13099 library.
The sample application sets the clock frequency to the timer at 16MHz....
Looking around to develop hardware/software using the RAK4600 module!
RAK4600 (lora Node) uses Lora as its main way to communicate with my Lora server (normal flow).
Consider...
Hello,
I would like to switch on a led of a nrf52840 dongle by pressing the buton of another dongle. I don't know which example to use from SDK 17.0.2 to make a master/slave...
Pairing is rejected after setting,
i)APP_ADV_DURATION to 0
ii)adv. flag in adv. init from BLE_GAP_ADV_FLAGS_LE_ONLY_LIMITED_DISC_MODE to BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE...
Hi,
I tried to implement the UART in my code, based on the UART example code. Just as in the example, I first define the struct with the pin numbers:
The pins in this...
I found there was a example in "nRF5_SDK_15.2.0_9412b96\examples\dfu\secure_bootloader\pca10056_uart\arm5_no_packs" .
Is there a applicaion example that when it recv a specific...
Hi
I need to connect to perticular central and i know the central MAC address. So i am using whitelisting in peripheral.
I made below changes in my code in ble_app_uart...
I am trying to use the gzp_dynamic_pairing example in SDK version 16 with Segger Embedded Studio and the PCA10040 dev board. There is no project for SES so I copied what I...
Hi,
I am working on nRF5_SDK_17.0.0_9d13099\examples\peripheral\uart project.
How can I increase the UART buffer? like if I have to receive 100+ bytes data how can I read...
I am using a nRF9160 DK. I'm using a Windows 10 system and setup the SDK using nRF Connect.
I've started to experiment with the serial_lte_modem project -- version 1.3.1...
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrfutil%2FUG%2Fnrfutil%2Fnrfutil_intro.html links to two pages which cannot be found: https://infocenter.nordicsemi...
Hi,
I am able to transfer data from my custom peripheral device with nRF52840, but data is moving much slower than it should.
I am writing 244 bytes into NUS within...
Hi,
I am trying to use Cbor library provided the SDK version 1.3.0, I have added the module in my prj.conf file, however the documentation (at the top of cborencoder.c)...
This is the name that is advertised when the device is in DFU bootloader mode.
I've copied the bootloader_secure_ble from /examples/dfu/ but I cannot find where to change...
