We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi All,
I use 2 peripheral and 6 Central roles coexisting.
Not clear the order of conn_handle number assigned by SD during BLE Connection.
For example.
After Central...
I am new to nRF programming. My "far away goal" is to make a BLE sensor mesh with a centralised data collection.
Currently I am deciding what libraries to start playing...
Peripheral device has 2 services,but central can find only 1 service(0x1001）.
I want to find other service(0x0001)
According to the message seems to be looking for 0x1001...
Hi,
I'm using the nRF51 dongle with nRF SDK 12.3.0 and the S130 2.0.1 SoftDevice to implement a BLE central. The dongle repeatedly connects to a BLE peripheral, performs...
I'm running the PB Remote Client on a PCA10040.
I have 2 servers running on PCA10040 boards.
Watching the log whilst debugging the client, I receive the following: ...
Hello all,
I am new to nRF platfrom, I am working on a protect which contains multiple BMD-200 modules with nRF51822 controller. It has to transfer some data via UART,...
Per this blog, I understand that the nRF52's ANT pin must be matched to 50ohm via L1/C3 and that the antenna must be matched to 50ohm. Hence a trace with 50ohm characteristic...
Hello, the title is pretty descriptive.
I've tried to read through previous questions and got a rough idea but decided that it would cost too much time for me to explore...
I am working on a ble application using an nRF51822 that requires low power consumption. I'm curious if on average the observer or the central role will consume less power...
We have our own custom board using nRF52832 (via Laird BL652 module). Until recently, we have been programming our application, bootloader and softdevice using the PCA10040...
SDK12 and SD 132 v3.
I have my code working for HVX from the peripheral. I can HVX send up to 80 bytes on one characteristic in one call (ATT MTU was set to 83 and DLE...
The NRF52 product spec suggests:
"The input buffer of a GPIO pin can be disconnected from the pin to enable power savings"
I've found that gpio.h provides the function...
Here is a snippet of my debug log:
nrf_sdh_freertos: Creating a SoftDevice task.
nrf_sdh_freertos: SoftDevice task not created.
app: ERROR 4 [NRF_ERROR_NO_MEM] at ...
