But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hello,
Setup:
nrf5340
ncs 2.9.1
Zigbee r23 add-on
I’ve implemented a custom ZCL cluster that acts as a data pipe. I’m trying to determine what the actual maximum...
It would be nice to be able to provision the KMU of nRF54l15 devices directly from the nRF Connect Programmer Tool. This is currently only possible using the nrfutil command...
Hi: Nordic Team
Environment: - SoftDevice: S332 (SDK16), ANT+ + BLE on nRF52 - Calling ANT APIs from app (e.g., sd_ant_channel_status_get, sd_ant_channel_rx_search_timeout_set...
Hello everyone!
I want to use BLE with the filesystem (FS), but I haven’t found any examples. When I enable BLE advertising, any filesystem operations stop working.
(...
Hello Nordic team,
I'm working with nRF Connect SDK (version 3.1.0) on an nRF54L15 device and using mcumgr for Bluetooth LE firmware updates via the SMP service.
My goal...
Hi,
I'm trying to run the nrf/samples/cellular/at_monitor sample (v3.2.1), but I keep getting this output.
I have two nRF9160 devkits, and they both are giving me this...
Hello,
I'm using the NORA-B106-00B-00 (nRF5340) on a custom PCB board. I can program the board, but there is no output i.e. print statements coming out of the board...
I build contact sensor example (use nrf connect sdk v3.2.1, nrf52840 chip) and try commissioning with apple home kit (use homepod mini), device commissioning succeed but cannot...
Hello! I'm currently working on a circuit design where weight and size are critical factors. Could you please tell me the minimum dimensions and weight of this chip? Thank...
I've made a new project as I had to change some hardware than the previous one.
The code seems fine, but I'm not able to load the libraries in the project.
A red underline...
When an ESD shock to the PCBA causes the nrf52840 to reboot, what reset code should we expect to show up with hwinfo_get_reset_cause()? RESET_BROWNOUT?
Using Zephyr NCS...
Hi! I am trying to use the LE Audio application and one of the samples in it, by including the necessary source files, and Kconfigs in my project. On the network core, I am...
As per the doc , when I use a smartphone (the base version is Android 12) to touch the NFC antenna, I should see a pop-up window:
3.Confirm pairing with ‘Nordic_HIDS_keyboard...
Is it possible to promote my project here: complete Zephyr development environment running solely on Raspberry Pi 4 Bookworm OS? If nothing else it does provide information...
Hi There,
During the transmission and reception performance test, I found that the LE1M's maximum sensitivity was only -92 dBm, while the LE2M's maximum sensitivity was...
