But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello, I'm starting to build/develop a project around the ISP2053 (nRF5340 module) and I'm a bit confused with the schematics. In some of the schematics, there is a "VDD_nRF...
Hi,
I am trying to subscribe to notifications from a peripheral device on my central device. The peripheral has more than 3 characteristics, but I am only able to successfully...
Hi,
DFU over UART is failing on NCS V3.1.1. I have a project file that works fine with V3.1.0. When I query the image information, MCU responds immediately. But when I rebuild&flash...
I now need to make a program on nrf5340 audio DK, SDK v3.0.2 to scan auracast and print the information in the subgroup in PA, without sink BIS.
In addition, it needs to...
Hello,
I am trying to use the drivers from the following repository: https://github.com/too1/ncs-arducam-mega-driver
I and using the latest version of the NCS 2.2.0, I...
Hello,
I get this error when I try `nrfutil device list`, and any other nrfutil device command.
However, if I use `nrfutil device --jlink-dll /path/to/libjlinkarm.so...
Hello,
My name is Jeon. I am using the RTC function on a custom board that utilizes the same chipset as the nRF9151. I have configured the RTC to trigger an alarm every...
Hello,
I need to make the OTA DFU work and I followed the instructions here: https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/samples/subsys/mgmt/mcumgr/smp_svr...
Hi,
Please note that we are having below setup
Module: nRF52832 based HolyIoT YJ-16048 Module SDK: NRF 17.0.2 Tools: Power Profiler Kit II
Expected current consumption...
Greetings,
Does anyone know if there are updates planned for the Arduino IDE with the latest SoftDevice versions? I opened this issue on GitHub: https://github.com/sandeepmistry...
I am using NCS 3.0.2 + VSCode to develop for the nRF54L15 . I have two projects:
\nrf\samples\bootloader\src
\nrf\samples\esb_prx
Since my custom board...
The instructions for running the sample are too difficult to follow. Here is why/where:
>>The sample also requires a device running a CTS Server to connect with (for example...
I am using nrf 52840dk board i need to know how to reset the devlopment using software reset when we press the Button 1 in the nrf 52840dk board
1. Give some software reset...
Hello,
I want to Configure a UART RX pin as GPIO and use it as a Wake - up interrupt pin before going to sleep. Is this possible in nrf54l15?
I tried to do so, but I was...
I've been having problems getting nRF Connect to flash a target through my J-Link programmer lately, even though it has historically worked fine. I suspected the issue might...
