This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Similar to ticket # 349557, we plan to operate nRF9151 in SLM mode and use both LTE and GNSS features. There is some interest in having GNSS (NMEA) data sent out on a dedicated...
Hi Team,
We have started our BLE development using nRF54L15 using SDK 3.1.0.
We have selected this MCU because it support all security features, we are going to start...
NFC certification and library.
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrfxlib/nfc/README.html tells me, NFC is supported by nrf52 and 53.
e.g. libnfct2t_nrf52...
I am using nrf54l15 with NCS v3.1.0 with the following error when i connect it(i worked in NCS v2.9.1 successfully):
Controller unresponsive, command opcode 0x2035 timeout...
We as a company love the app (nRF Connect) and use it accross a lot of devices to recover stolen goods with BLE.
However, on all my Android devices (modern tablets and phones...
I am working with St7789v driver based RGB565 Display . I have chosen SPI21 configured at 8Mhz and if I send 15 bytes chunk of image bitmaps, I can see the image in the display...
Hello, I am testing the system off demo on the nRF54L15 DK using nRF Connect SDK v2.8.0 (Zephyr v3.7.99). I ran the sample exactly as provided in the SDK .
Observed log...
I am using the nRF7002DK with the nRF5340 SoC. By default the board runs at 1.8 V until I provide 3.3 V on VIOREF. Currently, I am using another board just to drive VIOREF...
Hello there,
we're using multiple pwm-channels of one module of the nRF54L15 for different purposes (multiple motors, h-bridge control; depending on the project).
When...
Can my Power Profiler 2 be faulty?
It does the following in both source meter and ampere meter mode. I start to measure and it shows some microamps current that's expected...
I have a custom board that consists of a nRF52840 and a nRF7002 WiFi companion chip, connected via SPI. (not QSPI)
I wrote a tiny test program that configures the nRF7002...
I'm implementing an OAUTH procedure on my device. I'm able to access login.microsoftonline.com and get user and device codes, then after authorizing, I can access the token...
Currently, only the NRF5340 chip on the NRF5340 development board is powered. Now, we need to first test the Bluetooth performance of this chip. Open a standard example project...
