Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hello there,
I am that newby in the vs code dev environnement. I use the XM122 from acconeer to perform radar measurement. The soft provide by Acconeer compiles and works...
Dear Community;
I am trying to port this code that was made for an nrf52 to an nRF9160. I have a 4.99K pull-up resistor between the data line and VCC.
This is my ds18b20...
Hi, Is it possible to increase the size of the buffer for the UART IRQ RX function such that it receives more than 8 bytes at each interrupt? Currently I am trying to send...
Hello everyone,
I'm reaching out to touch base on the current support status on the latest software (MFW v1.3.1 and NCS v1.7.1) for CoAP over UDP (DTLS) for using as a main...
Hi,
I have a circuit with an I2C peripheral on a separate power switch. There is excessive power consumption (about 50µA extra) due to leakage after TWIM is disabled and...
Hi,
I am using a nRF9160-SICA-B1 and sometimes will see debug output that looks like this in Tera Term:
Glitch example:
Good example:
Basically it appears like...
Hi everybody,
I'd like to perform serial DFU on my nRF52832/nRF52840 based devices, using an external master MCU. Is there any reference C code for the master MCU? In this...
Hello. I am new to Zephyr. I cann't debug Hello_world sample. As i understand it always reboots and does not go to main.
I am trying to use VS Code and nRF Connect SDK ...
NRF Connect shows no device available.
usb interface MCU which embeds a j link is not detected by windows.
LED5 is blinking.
I have an external jlink to try to recover...
I had a project set up and working with my nrf52840 dev kit. It was using the 1.7.0 SDK and was based on the zephyr hello world sample. Today when I open VS Code, the project...
Hi,
On Segger Embedded Studio when you debug you also get the RTT console displayed at the same time. Is this possible on your VS code implementation? At the moment I can...
I'm trying to add 802.15.4 driver into my project (to implement an proprietary protocol).
The wireless_uart sample is very helpful and I got it up and running.
However...
I can find some other topics about this:
Like this one:
https://devzone.nordicsemi.com/f/nordic-q-a/43370/nrf_log_info-and-printf-does-not-work
or this article:
https...
Hello, I am new to firmware development and I am trying to stream heart rate data from an nrf32840 DK to an nrf32480 dongle and output that data. I am able to successfully...
