We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I'm designing around part 1490-1071-2-ND (nRF52840-QIAA)
Your ref designs show DEC5 decoupled with C9, 820pfF and states "not required for Fxx & later"
Do I need to place...
We are starting a new Nordic-based project and are looking through the nRF Connect SDK 1.7.99 documentation ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf...
Hi
In the documentation of the function " int at_cmd_write_with_callback ( const char * const cmd , at_cmd_handler_t handler ) " it is written that "CMS and CME errors are...
Hi,
What we are currently using is nRF52832, the central product is SDK16, and the peripheral product is SDK13.
Does SDK17 only support BLE Secure Mode 1 Level 4?
Are...
Hello. At first I m newbie and don't have experience with Thingy:52 and Embedded Segger Studio for ARM.
I m trying to work with my Thingy with Segger j link and SEGGER embedded...
I am trying to build the zephyr blink project using west :
I have installed the gnu-arm-embedded toolchain and set my environment variables accordingly : ZEPHYR_TOOLCHAIN_VARIANT...
Hello
The Uart Baudrate is initiliazed at 115200 baud but i the BLE nRF52833 is sending with about 115900.
I try to switch to hf clock but the baudrate is to high.
...
Hey,
I have a nRF central that connects and bonds to peripheral devices via BLE.
From what I understand, the peripheral device has a BLE MAC address that isn't consistent...
I am setting to NRF_SDH_BLE_CENTRAL_LINK_COUNT=1 ,it is working fine for ( 1 central and 1 peripheral )connection is fine(data also sending),but i am changed to NRF_SDH_BLE_CENTRAL_LINK_COUNT...
Hi
I am new to Nordic
I am using nordic nrf52832 with segger embedded software tool woth nordic support version NRF SDK 16.0.0
I am facing issue with build configutations...
Hello.
I would like to get an event that an advertised packet has been sent in a peripheral device. Is there a way to do this? Also, is it possible to get the channel used...
I'm using nRF9160DK and in that cJSON formation give me some error because of that my device will restart again and again
as in code if I'm input cJSON_AddNumberToObject...
Using SEGGER embedded studio for ARM (Nordic Edition) v5.60. using Project-> Configure nRF Connect SDK Project Fails in configuring MCUBoot in Zephyr.
No Documentation on...
