But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello,
I am trying to merge mqtt_simple and gps together. Each of them is working well on Thingy:91.
1. I am using lte_lc to configure the modem and enable PSM and eDRX...
Hello All,
Right now I am working with: https://www.digikey.ca/en/products/detail/circuit-dojo/PASSY-NRF9160-FEATHER/13668137 which I think is practically the same as https...
As everyone knows, the supply of semiconductors is pretty bad now. Normal suppliers such as Digikiey have zero stock. Recently we have had to purchase from less known distributors...
Hi everybody! My application is based on SDK 17.02. I try to communicate with an spi device using spim driver and the code is basically based on the nrfx-spim example.
After...
I am using latest version, nrf connect sdk v1.4.99-dev1
when activating bt_enable, application gets stuck
applications without BLE works well
I am working with...
Hi I'm Frank.
I'm testing Serial DFU via UART using TWO nRF52840 DKs(DFU master and DFU slave DK).
I want to update firmware of slave DK through the master DK.
I was...
dear all:
I use the latest sdk17 to test the ANCs sample on the 52840 DK。 The address of the example is: SDK_Path\examples\ble_peripheral\ble_app_ancs_c。after...
I have a example application (gatt central) that works fine on the nRF52DK dev board. I'm able to change the advertisement name, connect to it with my phone, and see the characteristic...
Hello everyone,
Yesterday I found a strange behavior with the NRF9160 GPS on NCS v1.5.1:
When configuring the GPS to run in Single Fix mode, running on MFW v1.2.3, I noticed...
*** edit: Problem solved. My project file had build config set to "release", I had to change it over to "Debug".
Kindly close the case ***
I have an i2c program running...
Hello,
I would like to ask for guidance, as I am at the very start of a human interface device (HID) controller development, considering BLE nRF52840.
The use case I would...
Hello!
I am trying to get basic communication between two nRF24L01+ modules to work on Teensy 4.0's, but I am having trouble transmitting and receiving.
Here is the wiring...
Hello, DK:nrf52810
sdk:17.0.2
In my project i have to advertise accelerometer and gyro value through beacon so i have done with using https://devzone.nordicsemi.com/f...
Hi Nordic Mesh experts,
I'm testing for the BLE mesh using light_switch example based on nrf5 sdk for mesh and nRF Mesh APP.
From the printed info on the APP during connection...
So I now have nRF 52840 dk and I'm working through the secure bootloader example. I am using SES. (Windows).
So I built and flashed the the app and it looks fine, it has...
