Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Using VSCode and the nRF Connect VSCode extension, each time a debug session is started the target is erased and programmed, regardless of whether the code was changed.
...
Dear Nordic TS,
I'm trying to power an nRF9161 DK with a simple external battery. According to the documentation, I thought that this battery voltage should be applied between...
Hi community,
I need to get data from the BMI270 sensor that is on the Thingy:53 board. I have already taken some previous topics as reference but I still haven't been successful...
Knowing, that the AS-RAI implementation is experimental, I would still prefer to have more documentation about the details.
I already asked for these details in an other...
I am working through BTLE Fundamentals, Lesson 6, Exercise 2, and running the code from blefund_less3_exer2 per the instructions and it all looks good on the app COM log:...
i'm already able to TX and RX arbitrary packets between my own bare-metal test programs running on a pair of DKs... since both programs used identical configurations (mode...
Hello! I am currently developing my own custom service with two nrf 52840 development kits where one acts as the Client and one acts as the Server. I have managed to set up...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
Wheh I try to debug a multi-domain-image on an nrf5340 or 52840, I can debug the mcuboot domain just fine. But when I try to debug the app-domain (I tried this with the zephyr...
Hi,
Using Visual Studio Code, when I build asset_tracker_v2 in NCS v2.9.1, for nrf9160dk/nrf9160.ns, I keep getting the problem shown in the subject line
equivalently...
Dear Team,
I have a question regarding preventing LTE from endlessly searching for a network connection. Lately I have been facing issues where LTE connection is rejected...
Hello everybody! It's my first question and I'm new at mcu programming. I hope for your understanding!
I have a task: count seconds using a counter and display them on a...
Hello,
I'm working with a custom board using an nRF5340 as its primary MCU and NCS 2.7.0. The application I'm developing requires internet connection and can ideally support...
Hi!
I am trying to power the thingy:91 from solar panels and have some issues with the thingy:91 restarting when the solar panel receives a medium amount of light. The solar...
