At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
nRFConnect sees the j-Link device, and everyone else sees the device.
I use this j-Link with Segger Embedded Studio.
What makes nRFConnect unhappy? Perhaps python2...
Does nRF51822 support uart over ble profile? I see in previous discussion "nRF8001 UART-over-BLE" talking about this and answer suggest 51 serial has this?
We want add MQTT...
Hi everyone.
I have problem with my device. I use Visual studio with visual GDB and I'm trying to use interrupts from RTC. Got from this site lot of examples and wrote some...
Hi,
I am running my nRF9160 DK in "nRF Only Mode" (Via SW1). I would like to drive the serial terminal out via one of the GPIO pins, connected to my MAC using an FTDI serial...
SDK v15.2.0 using peripheral spi example. Windows 8.1, uploading to nRF52 DK.
In my while loop I use bma_spi_read() twice with a small delay in between. The first...
Hi,
I am using the reliable message communication to measure Round-trip time based on the Light switch example.
I noticed that in high traffics, some packets are not...
I want to use TimeSlot API for nrf52832.
two question.
I want to use time slots regularly . I call follow, timeslot_open() timeslot_request() - timeslot_end() -> IDLE_STATE...
Hi there,
I've already asked about it https://devzone.nordicsemi.com/f/nordic-q-a/49701/commissioner-disable and I've tried it but nothing work. I've already spent 5 days...
I am in pre production with the nRF52840. My customers have access to the micro USB port on the device. I want them to be able to define a string for the nRF5 transmitted...
I am using nRF51, SD 130 1.0 and SDK 10.0.0. I have 11 buttons connected to nRF. Currently it only works for up to 4 buttons (APP_TIMER_OP_QUEUE_SIZE is 4, but I'm not sure...
Hi,
i am working on spi master example in nrf52832, when clock is set to 8MHz, clk signal output at the nrf52 pin is more like triangle wave.
is there any way to set pin...
Hi,
At the moment, my current location does not have an NB-IoT network for the nRF9160 DK to attach to. This means that the device is unable to activate PSM mode (which...
Working with SDK 15 on an nRF52832:
I have a peripheral applicatin where I'm computing the value of a BLE read on the fly.
Currently I do that by:
Setting up a BLE...
Dear dev community,
I've got a very simple question: How can I see the subscription and publishing addresses list in any mesh node for any model?
Thank you!
Regards...
Hi I am developing a custom PCB for the nrf51822 chip. I heard the nrf51822 chips do not come with preloaded firmware or bootloader. Do I need to also flash the bootloader...
