At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
We are programming our nRF52 based boards through USB via the P20 connector on a Nordic nRF52-DK board. However when there is a problem with our board, e.g. if it did not...
Hi,
I am working on an application using NRF52810/NRF52832 without Soft Device (I don't need BLE for this app), on a custom board. I am using the SDK15.
There is no external...
Hello,
I run the example given in SDK V15.0.0 to measure Vdd of nRF52-DK:
NRF_DRV_SAADC_DEFAULT_CHANNEL_CONFIG_SE(NRF_SAADC_INPUT_VDD);
I don't change the default...
Before I explain my issue I wanted to be sure on my basics, so here is my understanding after doing the research in nordic devzone
I'm using nrf52832 with sdk15
1) BLE...
I am using nRF5_SDK_15.0.0_a53641a.zip to create an application needs paring and bond. Now I got a problem that, if a smartphone removed the bond manually in its phone settings...
Hi
I’m using NRF51822_XXAC + s130_nrf51_2.0.0_softdevice, my program work well most of the time, but it dies at 0x000006b0 sometimes. Since I used the S130 softdevice, the...
Hello, guys,
I develop 52810 with sdk 14.1.0, i need the OTA features,
but i couldn't find the dfu demo( ble secure dfu bootloader and
buttonless dfu template app , pca10040e...
Hello,
As we know that nRF52840 SoC supports Bluetooth 5's 4x Long Range and 2x Data Throughput.
How different PHYs for these features (2 Mbps PHY and 1 Mbps Coded PHY...
Hi,
I am using nRF52832 to design a mesh system, starting with light.
Everything is fine, and development is reaching the end.
Before today, I use only one model,...
Hi there!
I had some great help on my last article about getting started. I'm now using Segger Embedded Studio and the nRF SDK Version 15.
Before I get too deep into BLE...
I'm developing multiple peripheral and a central. Central is only scanning and Peripherals are only advertising.
In the example, I see that I should use the ble_app_blinky...
I get a BLE_HCI_CONNECTION_TIMEOUT error when I use NRF connect to connect to my dev board only when my dev board is using SD 6.1.0.
Once I get the error I have to reset...
