We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I am on the learning curve of nRF9151 and LTE/GNSS.
Trying to build and run the sample app under nrf/samples/nrf9160/location
The errors Im getting are
[00:11:23.476...
Hi, I have upgraded my custom nRF52840 devices from SDK 2.4.1 to SDK 3.0.2. For few days, these devices did connect to existing OpenThread network. But now, all SDK3.0.2 devices...
I used the Bluetooth mesh distributor example from ncs2.9.1, and the Bluetooth mesh dfu can proceed normally. However, when I tried to pause and resume the dfu process, I...
Dear Nordic Support Team,
nPM2100, SHPHLD pin: we would like to connect a pushbutton to GND to wake the PMIC from ship mode. Additionally, we would like to read the pushbutton...
Hello, I am currently designing a custom board using the nRF9151 and I have a question regarding the SWD interface. My understanding is that the nRF9151 contains two main...
I've just spent about 4 hours trying to figure out why a particular build was failing (on nrf9151dk).
Examing the cryptic errors finally revealed that the TFM partition...
We're using the nPM1300 in our designs and we noticed that the charge portion does not appear to keep a battery charged when USB is connected for extended periods.
Our arrangement...
So far we have been using nRF5 SDK v17.1, but we ended up using nRF connect SDK v1.9.1.
However, this compiles too slowly.
I modified main.c and it seems to compile everything...
Hi,
I’m using NCS v3.1.0 and noticed that my application does not run unless I enable:
CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC=y
Without this configuration, the system fails...
HI TEAM,
I am using a custom board and measuring its overall current consumption using the NRF Power Profiler Kit 2 (PPK2) .
Setup details:
Power source: External...
Hi,
We are using the nrf9151 to get GNSS data/coordinates without using A-GNSS, we followed the information in the following page "https://docs.nordicsemi.com/bundle/ncs...
Hello Nordic Support Team,
We are currently developing an IoT product using the nRF9151. In our application, the device wakes up once per day, transmits a small amount of...
Hi, everyone
I am currently working on the development of Bluetooth and ANT+ on the nRF52832 chip. It communicates with my chip via UART, and now there are occasional disconnections...
